Hawk 250 parts

[Ojorax]

Hello I'm parting out my crashed hawk 250 message me if your interested or you can shoot me an email with the title "Hawk250" if you'd like more pics or have questions :thanks:

Engine still has compression and hasn't leaked any oil (around 800 miles on it) still shifts through all the gears by hand ok it seems I haven't gotten it started since the accident though

Have a few original left over as well

Ojorax@gmail.com

[Ojorax]

Sold Tail light and MSR shifter

[nickdowny]

How much for the rims front and back shipped to 97078? Want to have a more street dual sport pair and more dirt dual sport pair so I don't have to compromise or be changing tires all the time.

[Emerikol]

Ojo, how much for the rest of the bike whole, and where are you located?

-Emerikol

[roundhouse]

Did nickdowny get the wheels? He obviously got first dibs but I need a front.

[3sticks]

hello have you jetted and adjusted carb (jets and needle) i need one that has been already jetted and needle adjusted....if so how much to ship to 60073.....also did you upgrade the sprockets at all
thanks
JB

[Ojorax]

bump

[Lit Hawk]

I could really use rear master cylinder, speedo cable, dust cap off steering, and rear brake pedal. I sent you an email a while back and never got a response. Also the horn

[W0X0F]

Hello,

Sorry to see that you wrecked you bike, and hope you are all healed up!

I just recovered my bike form a theft, and need some parts,

What plastic parts do you have that are usable?

Is the rear license plate light usable?

Is the seat okay?

How are the ignition switch and key? Also the fuel cap and helmet lock?

Thanks for your time!

[Painlesstom]

Dash survive? Don't care if the speedo works.

[JerryHawk250]

Dash survive? Don't care if the speedo works.
I have one that is working. I replace mine with a digital. I think it has about 800 kilometers on it.

[rj2455]

Exhaust available?
Id assume the front wheel is gone.
Headlight?

[Pathfinders]

j2455 I have a exhaust you that has less than 100 miles on it for free. Might not be worth shipping though. What is your location.

[nij_tp]

Hi, hope you are ok. This is probably really stupid but do you have the rubber gasket that goes round the air box, I took the top off to modify and there is no gasket! (brand new bike with 0.4 miles on it!!) Shipping 03031

Thanks

[JerryHawk250]

Hi, hope you are ok. This is probably really stupid but do you have the rubber gasket that goes round the air box, I took the top off to modify and there is no gasket! (brand new bike with 0.4 miles on it!!) Shipping 03031

Thanks
There is no gasket. Air box doesn't seal up well and dust will get sucked in. That's why I switched to a pod filter.

[NzBrakelathes]

There is no gasket. Air box doesn't seal up well and dust will get sucked in. That's why I switched to a pod filter.

The top lid? doesn't need a gasket as filter is the seal

[NzBrakelathes]

Hi, hope you are ok. This is probably really stupid but do you have the rubber gasket that goes round the air box, I took the top off to modify and there is no gasket! (brand new bike with 0.4 miles on it!!) Shipping 03031

Thanks

Look again at the lid - why have a gasket?
the filter it self is the seal etc

[JerryHawk250]

The top lid? doesn't need a gasket as filter is the seal

The bottom portion is in two pieces too. Dust gets sucked right through. I probably could of put silicon to seal it off.

[Megadan]

Look again at the lid - why have a gasket?
the filter it self is the seal etc

Except the filter seals to a section that bolts to another lower section, and that is not sealed.

[NzBrakelathes]

This part? Lid has no seal
Or are you asking for next later down?
I have an air box without a hose if parts from it help etc

[nij_tp]

There is no gasket. Air box doesn't seal up well and dust will get sucked in. That's why I switched to a pod filter.

Oh ok, I thought there was a channel that looked like it housed a rubber seal.

[krawl]

My air filter lid came with a rubber gasket, it is just a round rubber strip cut to length and partially fell out as I took the lid off. I had to stretch it as I placed it back into the slot around the outer edge of the lid to make the ends meet.