Go Back   ChinaRiders Forums > Members List

SpudRider SpudRider is offline

Visitor Messages

Showing Visitor Messages 1 to 10 of 54
  1. outboardr
    10-31-2023 04:37 PM
    outboardr
    Spud, do you still ride a Versys X 300?
  2. Thumper
    02-09-2022 03:36 PM
    Thumper
    Hi spud! I found your images of the Qingqi Forks, and they look suspiciously similar to the forks on my Bashan Brozz. Inverted, but not true dual reservoir cartridge forks!
    I took one off yesterday and intend to open it up tonight. Did you take any picks?
    I am going to use a caliper and get dimensions on the damping rod, piston, other parts and assess the situation for installing Racetech cartridge emulators. Racetech has lots of different applications, so I will need to provide them with spring width and inner diameter, and the diameter of the top of the dampling rod to select a compatible emulator. I am sure they will have one that fits. Did you install them???
    Thumper (Andrew)
  3. ccubanito
    01-29-2022 06:43 PM
    ccubanito
    I need your heeelp. I'm in the search for parts for my 2006 Zongshen Sierra 200. I need the wiring harness and CDI. Were can I get parts for this bike now a days?
  4. Tylor_is_Here
    12-18-2019 09:06 AM
    Tylor_is_Here
    Spud,

    Where would I go to purchase an engine for an 06 zs200gy-2? Thanks!
  5. acecase09
    12-09-2019 06:44 AM
    acecase09
    Got a discussion question for you and I want your opinion. I have a 2019 rx3, its new, <250 miles, and the front brake on mine sucks ass. Now it does have abs, and before I go bypassing that I was wondering about something else. I searched and read here and elsewhere, but i have not come across anything about brake lines. With the abs under the tank, the front line is about 7' of total line, the rear is about 4'. That is a lot of line under the best circumstances, and line flex has always been one of the places that you loose a lot of pressure. I have not put a pressure gauge on it and seen what kind of pressures I am getting and holding, but with the factory lines being so long, and likely cheaply made, do you think that braided lines will make a huge difference? Do you know if anyone has swapped them out and what were the effects? When I do the first valve check, I think I am going to measure them and order new stainless braided one? What are your thoughts?

    Thanks,
    -ace
  6. Orlando texas
    02-17-2019 09:07 AM
    Orlando texas
    Hi Spud. Wandering what's your milage at on the RX3 I got a 2017 blue also just wondering if they can make it all the way to 50,000 miles I'll be happy
  7. GlennR
    10-16-2018 08:59 AM
    GlennR
    Hey Spud,
    Where have you been? Out riding I hope.

    Cheers,
    Glenn
  8. Meloman
    05-25-2018 06:06 PM
    Meloman
    Spud is that a 21” wheel on your RX3 ? If so, was it just plug and play or did it require a lot of modifications ?
    Thanks,
    Mel
    (Meloman)
  9. Elwir
    05-24-2017 08:23 PM
    Elwir
    Hey iv been reading your forums for a few months now and finally decided to take action on the cheap diy led headlight conversion for the crf250x. I bought one from china for $13, disconnected my stock headlight assemble from my tusk hi lo control switch (i made the stock bulb do hi lo b/c its dual filament) and directly connected the led bulb with the same color wires to the switch and it worked well. hi lo, and unscrewed the fan and put a scrap aluminum to block it. Put it all together and it was amazing. But after a hour long trip the led bulb stopped working and i was forced to use my back up led bar thats connected to my battery.. Bought another led bulb, same one, and a cheap universal 4 pin 12v DC R/R $9 thinking i could just wire it up and replace the stock one. Tired it and it still doesn't work. So i am left here confused and would love some advice. Will i just need to spend $170 on the trail tech stator and r/r plus wires?
  10. Lous
    05-12-2017 01:39 AM
    Lous
    Hi Spud my name is Louis and iam new to the forum. I own a ZongShen 200GY-2. i fixed the carburetor because the engine was not performing when i eventually managed to fix it the bike started right up. Long story short i switched the bike off 2days later go back wanting to start it and its dead. Checked for spark and nothing. I then went straight to stator cover side took it off and saw that the stator was shaving against the magneto causing the Source coil to burn.

    I had it rewired and expected that once fitted the bike would start and still nothing. I did not suspect the CDI would be faulty as it was working but now i seem to think it is that. Ive tested the stator ohms is 1.4 per wire the resistance in the rewired source is very high though being 820ohms and the Pulsar coil is about 680 Ohms. Ive checked all the ground wires. Now the bike i tested the ignition coil and rectifier on is sold so i cannot test the CDI on it.

    Could you please give me some advise

About Me

  • About SpudRider
    Location
    Idaho
  • Signature
    Spud

    "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain

    2015 Zongshen ZS250GY-3 (RX3)
    2006 Zongshen ZS200GY-2 (Sierra 200)
    2005 Honda XR650L
    2004 Honda CRF250X
    1998 Kawasaki KDX220

    Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894

Statistics

Total Posts
Albums
Visitor Messages
Thumbs Up?
  • Thumbs Up Received: 969
  • Thumbs Up Given: 1,094
General Information
  • Last Activity: 10-04-2023 12:26 AM
  • Join Date: 07-01-2008
  • Referrals: 28

Friends

Showing Friends 1 to 1 of 1

All times are GMT -4. The time now is 05:50 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.