Go Back   ChinaRiders Forums > Search Forums
Register FAQ Community Calendar Today's Posts Search
Showing results 1 to 16 of 16
Search took 0.01 seconds.
Search: Posts Made By: Nick Nitro
Forum: Street 05-02-2022, 07:20 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
Well I finally got the new boot installed, came...

Well I finally got the new boot installed, came to life but was too rich still. Switched to a 38 Slow with the 125 Main, backed out the idle speed screw. Perfect!!

Got some new foot pegs installed...
Forum: Street 04-27-2022, 07:09 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
That was a typo on my end, it's a 36T sprocket....

That was a typo on my end, it's a 36T sprocket. :doh:
Forum: Street 04-27-2022, 07:07 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
100%, I'm taking it to Grattan in Michigan in...

100%, I'm taking it to Grattan in Michigan in August. I should have it built to its absolute limits by then hopefully.

Just want to see what it can do before I swap either a Husqvarna 701, CR500,...
Forum: Street 04-26-2022, 08:53 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
I found an aluminum one on Amazon that will be...

I found an aluminum one on Amazon that will be here Friday so I'll be able to finish it then. I also have a 32T sprocket on the way and utilized the measurements in your YouTube video.

Next will...
Forum: Street 04-26-2022, 06:13 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
Well... slide was just a hair off from fully...

Well... slide was just a hair off from fully closed. Fixed that. Then swapped from the 32 Pilot to the 40, much better but RPM's were all over the place. Carb boot is torn...

Any idea where to get...
Forum: Street 04-24-2022, 05:39 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
That might explain why in the 150 miles I put on...

That might explain why in the 150 miles I put on it today that near the end of the day it wouldn’t stay running at all unless I kept on the throttle. It got very lean out of nowhere. I’ll dig into...
Forum: Street 04-23-2022, 04:25 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
I apologize for so many updates to this thread. ...

I apologize for so many updates to this thread.

Came back to it because it was driving me nuts. Ended up going with the clip in the number 2 spot on the needle, a 130 Main, a 32 Pilot, and a lot...
Forum: Street 04-23-2022, 12:05 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
Went through and tried every single possible...

Went through and tried every single possible combination with the jets I have, the 5 needle clip positions, 1/8 turn adjustments on the idle, and 1/8 turn adjustments on the air/fuel screw. No matter...
Forum: Street 04-23-2022, 10:15 AM
Replies: 186
Views: 41,613
Posted By Nick Nitro
Well, I adjusted the throttle cable. 20-80%...

Well, I adjusted the throttle cable.

20-80% throttle is good but not great so the needle clip in position 1 out of 5 seems to still be okay but may need to change.

80-Full throttle is great so...
Forum: Street 04-23-2022, 09:17 AM
Replies: 186
Views: 41,613
Posted By Nick Nitro
That’s what I’m starting to think honestly. Gonna...

That’s what I’m starting to think honestly. Gonna start digging into it again here shortly. Gotta get some more coffee in me.
Forum: Street 04-22-2022, 09:26 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
We checked that. All good. At a 130 Main and 32...

We checked that. All good. At a 130 Main and 32 Slow now with the pod filter on. Best RPM with idle screw and air/fuel mixture screw adjusted with choke turned off is about 4,000 RPM now.

S. O. S....
Forum: Street 04-21-2022, 07:40 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
So I have the carb you recommended installed....

So I have the carb you recommended installed. Currently at a 115 main and 40 slow. Lowest idle RPM I can get is about 4,000 RPM and giving any throttle kills it. What jetting would you recommend? I...
Forum: Street 03-29-2022, 08:30 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
Still waiting for it to warm up here in Northern...

Still waiting for it to warm up here in Northern NY

https://myalbum.com/album/xu2GVxoVkE9eCo/

In other news, just got word my X22R is being delivered on April 8th!
Forum: Street 03-29-2022, 01:50 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
Thanks again Jerry!! Looking forward to your...

Thanks again Jerry!!

Looking forward to your next video!
Forum: Street 03-29-2022, 01:23 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
Thanks for the info!! Just to clarify then,...

Thanks for the info!!

Just to clarify then, the big bore kit would essentially be useless with updated engine?
Forum: Street 03-28-2022, 07:02 PM
Replies: 186
Views: 41,613
Posted By Nick Nitro
Hi Jerry, First off, big fan of your YouTube...

Hi Jerry,

First off, big fan of your YouTube channel. Extremely informative and actually learned a few things to help me with my CB750 project. Also, was the final push to order my own X22R after...
Showing results 1 to 16 of 16

 
Forum Jump

All times are GMT -4. The time now is 06:54 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.