Go Back   ChinaRiders Forums > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search
Page 1 of 2 1 2
Showing results 1 to 25 of 34
Search took 0.01 seconds. Search: Posts Made By: Rob G
Forum: ATVs 05-03-2020, 04:59 PM
Replies: 9
Views: 1,845
Posted By Rob G
In fact I do. They are an M4-.7X12mm. If you're...

In fact I do. They are an M4-.7X12mm. If you're going to notch the factory screws to remove them, just be careful not to get into the float bowl with the cutting wheel or it may break tightening it...
Forum: ATVs 05-03-2020, 04:07 PM
Replies: 28
Views: 2,998
Posted By Rob G
So he ran the power to the switch to a key-on-hot...

So he ran the power to the switch to a key-on-hot meaning the switch won't activate the winch unless the key is on. The switch itself draws very little power since it actuates a relay in the control...
Forum: ATVs 05-02-2020, 10:36 AM
Replies: 6
Views: 713
Posted By Rob G
I use a dremel tool with a cutoff wheel to cut a...

I use a dremel tool with a cutoff wheel to cut a notch in the float bowl screws, then use a flathead screwdriver to remove them. Replace them with new screws. Then use a drill and drill a hole in the...
Forum: ATVs 05-01-2020, 09:04 PM
Replies: 5
Views: 1,007
Posted By Rob G
Sounds like the transmission output shaft may...

Sounds like the transmission output shaft may have broke. Try taking the cover off where the chain goes into the engine and inspect.
Forum: ATVs 05-01-2020, 07:48 PM
Replies: 28
Views: 2,998
Posted By Rob G
Phew, glad you got it found and fixed. On my Bull...

Phew, glad you got it found and fixed. On my Bull 200, I ran an aftermarket fuse and relay box to hook up my winch, LED lights, cigarette lighter etc... just to be safe and to isolate as much from...
Forum: ATVs 05-01-2020, 07:23 PM
Replies: 28
Views: 2,998
Posted By Rob G
Always start with undoing what was changed, so...

Always start with undoing what was changed, so disconnect everything you added. Then, check the main fuse under the seat. If that doesn't identify the problem, it may take some DMM work. PM me if you...
Forum: ATVs 05-01-2020, 07:14 PM
Replies: 11
Views: 2,182
Posted By Rob G
Just as a general rule: idle is determined by the...

Just as a general rule: idle is determined by the idle jet, obviously the idle screw, the idle mixture, and the arc in the slide. From idle to 1/4 throttle is mostly the pilot jet and slide arc. From...
Forum: ATVs 04-29-2020, 10:55 PM
Replies: 28
Views: 2,998
Posted By Rob G
That is the battery acid and the battery vent...

That is the battery acid and the battery vent tube.
Forum: ATVs 04-13-2020, 01:19 AM
Replies: 8
Views: 1,028
Posted By Rob G
:clap: That's some good work. Thanks for the...

:clap:

That's some good work. Thanks for the update, now I know what to keep and eye out for and, should something act up in wet conditions, where to start.
Forum: ATVs 04-10-2020, 04:13 PM
Replies: 8
Views: 1,028
Posted By Rob G
Always seems to be the way of it. Curious to hear...

Always seems to be the way of it. Curious to hear what you find.
Forum: ATVs 04-10-2020, 02:15 AM
Replies: 8
Views: 1,028
Posted By Rob G
Round about '96 I worked on a pickup in the shop...

Round about '96 I worked on a pickup in the shop that had suffered an engine fire before. The owner put a new harness in it and everytime it rained he had all sorts of gremlins. Looking at the...
Forum: ATVs 04-10-2020, 02:05 AM
Replies: 4
Views: 860
Posted By Rob G
Been there man. All too many times. 35 years as a...

Been there man. All too many times. 35 years as a mechanic has taught me exactly what you stated "trust the process."
Forum: ATVs 04-10-2020, 01:57 AM
Replies: 4
Views: 624
Posted By Rob G
I have noticed a similar trend. Someone with...

I have noticed a similar trend. Someone with better knowledge of the supply chain can correct me if I'm wrong, but I believe whoever is making these components, they sell them to everyone in the...
Forum: ATVs 04-09-2020, 01:13 AM
Replies: 4
Views: 860
Posted By Rob G
Funny how that sound can travel like that huh?...

Funny how that sound can travel like that huh? Glad you found it.
Forum: ATVs 04-07-2020, 11:43 AM
Replies: 4
Views: 609
Posted By Rob G
Thanks Al. After you posted this I did some...

Thanks Al. After you posted this I did some poking around on Amazon and other places, seems that the problem you have is relatively common. I think, since this is on my kids quad I'll go back to...
Forum: ATVs 04-07-2020, 11:14 AM
Replies: 18
Views: 1,846
Posted By Rob G
Flashlightboy is right, this is a very dead horse...

Flashlightboy is right, this is a very dead horse that's been beaten way past necessary. It all comes down to what you want to do really. I leave those nuts because I see their purpose and I don't...
Forum: ATVs 04-07-2020, 11:04 AM
Replies: 8
Views: 1,028
Posted By Rob G
:tup: I second what Mudflap said. Second the...

:tup:

I second what Mudflap said. Second the carburetor has a vent on it, if water gets in there it will add water to the fuel in the float bowl. Also, electrical things don't particularly like...
Forum: ATVs 04-06-2020, 12:52 PM
Replies: 18
Views: 1,846
Posted By Rob G
Phillip; you are 100% correct. The adjuster bolts...

Phillip; you are 100% correct. The adjuster bolts are what we usually call a jack bolt and are used in surplus in the automotive world too. If the bolts on the pivot were designed to hold the axle in...
Forum: ATVs 04-05-2020, 12:59 PM
Replies: 18
Views: 1,846
Posted By Rob G
:tup: Haha. Well first I drew it and took a...

:tup:

Haha. Well first I drew it and took a picture of it but then remembered I had one outside I could just take a picture of that one instead. Happy to help.
Forum: ATVs 04-05-2020, 12:43 PM
Replies: 18
Views: 1,846
Posted By Rob G
This is my daughter's tforce, but should be...

This is my daughter's tforce, but should be pretty much the same.
Forum: ATVs 04-05-2020, 12:27 PM
Replies: 18
Views: 1,846
Posted By Rob G
Yes, you must loosen the two bolts on the...

Yes, you must loosen the two bolts on the eyelets. Likewise, on one of the bolts (if not both) there should be a nut on the other side of the plate where the eye bolts go through. Here's my procedure...
Forum: ATVs 04-04-2020, 11:15 PM
Replies: 4
Views: 609
Posted By Rob G
Aftermarket ignition box problem on Tforce

So, my daughter's Tforce was having problems running above about 1/2 throttle on our last ride. Got it home and dug into it to find a horribly carbon fouled plug. I tore into the carb and found...
Forum: ATVs 04-04-2020, 10:59 PM
Replies: 1
Views: 580
Posted By Rob G
I don't know on that one, but one of the best...

I don't know on that one, but one of the best resources I've found yet for gearing and information is whygostock. Might be worth checking with them.
Forum: ATVs 04-04-2020, 10:48 PM
Replies: 28
Views: 2,633
Posted By Rob G
One thing to note, the slide can go in either way...

One thing to note, the slide can go in either way but will only run right one direction. On the LEFT side of the carburetor is the idle adjustment screw (don't mess with the one on the right side,...
Forum: ATVs 04-04-2020, 10:35 PM
Replies: 7
Views: 2,584
Posted By Rob G
I can't speak to the Apollo, but my wife and I...

I can't speak to the Apollo, but my wife and I have 2 Tao Bull 200 and they have been great machines. However, my friend just bought 2 Tao Raptors for him and his girlfriend and they have been...
Showing results 1 to 25 of 34
Page 1 of 2 1 2

 
Forum Jump

All times are GMT -4. The time now is 08:51 PM.

Contact Us - ChinaRiders.net - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.