ChinaRiders Forums - View Single Post

pcspecialist · 05-18-2016, 02:19 PM

I cut off the buckles (leaving the loops intact) and drilled some holes in the seat pan to get a Coleman Comfort Ride(TM) Seat Protector to fit like a glove. http://www.amazon.com/dp/B006JMK7N8

Code:

http://www.amazon.com/dp/B006JMK7N8

Trunk fit beautifully, just needed some large nuts to raise it enough that I can get the seat on and off and the rear slots had to be filed a little bit to line up with the bolt holes on the Hawk. The trunk is easily removed, just turn the key and press a button. Now I just need a tank bag and some saddle bags.

http://www.ebay.com/itm/351721854900

12" X 3.5" OWNER MANUAL CANISTER
http://www.ebay.com/itm/111693466254

NGK (2202) DPR8EIX-9 Iridium IX Spark Plug
http://www.amazon.com/dp/B000CSGWZC

MSR DR-Z400 shifter (1 inch longer than stock)
http://www.amazon.com/dp/B000WJAVJ4

With the stock carb, I removed the plug over the idle mixture screw and turned it out 1 3/4 turns. I used a center punch to indent and then tap off the tamper proof screws, shimmed up the needle with three #4 washers and replaced the main jet with a large round size 110 (N100.604/110).
http://www.ebay.com/itm/171069472877

Replaced the front sprocket with a 17 tooth one. Discovered you can't get the cover back on with the chain on the 17 tooth, have to put the chain on after the cover is installed.
http://www.amazon.com/dp/B004DNA0KA

05-18-2016, 02:19 PM	#1
pcspecialist Join Date: May 2016 Posts: 583	Hawk upgrades, mods and accessories I cut off the buckles (leaving the loops intact) and drilled some holes in the seat pan to get a Coleman Comfort Ride(TM) Seat Protector to fit like a glove. http://www.amazon.com/dp/B006JMK7N8 Code: http://www.amazon.com/dp/B006JMK7N8 Trunk fit beautifully, just needed some large nuts to raise it enough that I can get the seat on and off and the rear slots had to be filed a little bit to line up with the bolt holes on the Hawk. The trunk is easily removed, just turn the key and press a button. Now I just need a tank bag and some saddle bags. http://www.ebay.com/itm/351721854900 12" X 3.5" OWNER MANUAL CANISTER http://www.ebay.com/itm/111693466254 NGK (2202) DPR8EIX-9 Iridium IX Spark Plug http://www.amazon.com/dp/B000CSGWZC MSR DR-Z400 shifter (1 inch longer than stock) http://www.amazon.com/dp/B000WJAVJ4 With the stock carb, I removed the plug over the idle mixture screw and turned it out 1 3/4 turns. I used a center punch to indent and then tap off the tamper proof screws, shimmed up the needle with three #4 washers and replaced the main jet with a large round size 110 (N100.604/110). http://www.ebay.com/itm/171069472877 Replaced the front sprocket with a 17 tooth one. Discovered you can't get the cover back on with the chain on the 17 tooth, have to put the chain on after the cover is installed. http://www.amazon.com/dp/B004DNA0KA Last edited by pcspecialist; 05-19-2016 at 08:49 PM.
	4