![]() |
#1 |
Join Date: Mar 2014
Location: Mexico
Posts: 134
|
Countershaft Sprocket Replacement
Guys, I learned my Vento's countershaft sprocket is worn and need to be replaced. I stopped by Yamaha dealership and asked about the sprocket. They don't have it but will order as soon as I pay the half ($13) and will get it by next week. I read Soud's thread "Zongshen Sierra 200GY-2 Countershaft Sprocket Replacement" but not sure if the Yamaha c. sprocket is the same as the PBI sprocket Spud used . I wonder if the Yamaha's sprocket will fit the Vento's countershaft.
![]()
__________________
Hector Mountrack Vento 2006 |
![]() |
![]() |
#2 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
I believe them to be identical. I'm using a PBI on my Yamaha.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
![]() |
#3 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Yes, you can use the Yamaha, TW200, counter shaft (C/S) sprocket, or any aftermarket C/S sprocket designed for the Yamaha TW200.
![]() ![]() Please note, you are going to need to drain the engine oil, and remove the entire, left crankcase cover in order to replace the C/S sprocket. Therefore, I suggest you strongly consider doing the crankcase cover modification shown in the following thread. ![]() http://www.chinariders.net/showthread.php?t=5081 I suggest you also purchase a new gasket for the left crankcase cover. You might damage the original gasket when you remove the cover. ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#4 |
Join Date: Mar 2014
Location: Mexico
Posts: 134
|
Thanks guys for your help. I will stop by the Yama's shop to order the c.s. this wed. I did remove the crankcase already in order to clean up the electric starter (it's been failing, sometimes work, sometimes not). I had to remove the left crankcase due to the way it was installed the screw on the starter. I got a hex bolt (same size) and will mount on the right side (head bolt) in case the starter needs service. Also, I will check the jet needle's notch (if it's at the middle, the third one) and remove the main jet to get the kit or a bigger one. However, 3 of 4 are stripped bolts
![]() ![]() ![]()
__________________
Hector Mountrack Vento 2006 |
![]() |
![]() |
#5 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
So we're clear, can you show us where the stripped bolts are located?
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
![]() |
#6 |
Join Date: Mar 2014
Location: Mexico
Posts: 134
|
The stripped bolts are those holding the carb bowl. I used the dremel and flat screwdriver to take them off. I removed the main jet and took it to the shop but nobody sells this guy. On the other hand, Honda (according to Spud's suggestion) sells the oil seal fork for $30 each one which I think is very expensive. Is there another model or what about the seals that use the TW200? maybe they're cheaper than the Honda ones.
__________________
Hector Mountrack Vento 2006 |
![]() |
![]() |
#7 | |
Join Date: Aug 2013
Location: Goodyear, Arizona
Posts: 410
|
Quote:
when you find the part # you should be able to order it from an industrial supply store. I recently bought some 35mmx25mmx4mm oil seals for about $6 each. I would think the fork oil seals are similar.
__________________
2020 Tao TBR7 9.3:1 PnP head CRF230F exhaust 4 degree advance key 290 degree cam Nibbi PE30 and cone filter Front fork brace |
|
![]() |
![]() |
#8 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
X2.
If you can take your seal sample into a local bearing shop, they might be able to match it. Have you looked at www.jetsrus.com?
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
![]() |
#9 |
Join Date: Mar 2014
Location: Mexico
Posts: 134
|
Nope but I will do it. Thanks for the tip.
__________________
Hector Mountrack Vento 2006 |
![]() |
![]() |
#10 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
![]() http://www.chinariders.net/showthread.php?t=10266 Outside diameter: 50 mm Inside diameter: 37 mm Thickness: 11 mm Besides getting the fork oil seals for the '09 Honda CRF150R, you can also purchase the Zongshen, fork oil seals from Taobao. ![]() As I detailed in my carburetor jet thread, you Teikei MV28 carburetor can use Mikuni N102/221, main jets, which you can purchase from Rocky Mountain ATV. http://www.chinariders.net/showthread.php?t=6501 http://www.rockymountainatvmc.com/p/...in%20jet%20150
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
![]() |
![]() |
#11 |
Join Date: Mar 2014
Location: Mexico
Posts: 134
|
Thanks spud for the oil seals size. By the way, I watched some videos on youtube about cleaning fork oil seals. In one of the videos, they claimed that nearly 90% of oil loss is due too dirt on seals. There is one product called Dr. Seal or sealmate (or soemthing) to clean up oil seals. I tried this approach but removing the dust seal was impossible
![]() ![]() ![]()
__________________
Hector Mountrack Vento 2006 |
![]() |
![]() |
#12 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
You're welcome.
![]() You can certainly try the SealMate; it doesn't hurt to experiment. ![]() ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#13 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
I've had good luck with a Sealmate, but I've only tried it on conventional forks.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
|
![]() |
![]() |
|
|