Warning: Fractured Wheel Bearing

[SpudRider]

Originally Posted by Eco Mouse

5 bearings totaled $22! For piece of mind, sounds good to me!...

Originally Posted by rtking

Wow - those are some dramatic photos. Given that, spending $22 for a set of spare bearings for peace of mind is cheap insurance.

Needless to say, I agree. My peace of mind is much improved now that I have replaced/serviced all of the wheel bearings.

[SpudRider]

Originally Posted by Eco Mouse

5 bearings totaled $22! For piece of mind, sounds good to me!...

Can you post a link to the vendor where you purchased your bearings? I'm sure others will appreciate knowing this information. Fortunately, I purchased a good supply of these bearings several years ago for my first Zongshen motorcycle.

[Eco Mouse]

As with any vendor, they might not be there a year from now...

http://www.amazon.com/6302-2NSE9-bea...A24Y2TWNNNOFW1

[2LZ]

This reminds me of the early Victory experience. SOME...not all...small handful of early Vics had some rear bearing failures, but it would take some miles. Most were two-up riders or heavy haulers. I made a point of changing my TC rear bearings with every rear tire. Once a bearing went, it hogged out the wheel so it needed to be replaced also. I wanted to avoid that. As stated, cheap insurance. I just sold the bike, with a zip lock baggy full of good rear bearings I replaced.
I got them from JC Whitney.

[SpudRider]

Originally Posted by Eco Mouse

As with any vendor, they might not be there a year from now...

http://www.amazon.com/6302-2NSE9-bea...A24Y2TWNNNOFW1

Thanks for posting the link.

[dpl096]

Originally Posted by SpudRider

Here is a photograph of the SKF 6202 2RS bearing I installed in the sprocket side of the rear hub. I only installed one of these bearings. The bearing in the brake rotor side of the hub is a 6302 2RS bearing.

I used the orange pick to pry open the rubber seals from the inside diameter of the bearing. I packed the bearings with Lucas Red "N" Tacky #2 grease. The photo also shows my 15 mm split collet, and the large driver I used to drive the old bearings from the hub.

Once again ... excellent pick up and tutorial !!
Have these been added to the cross reference sticky?

[SpudRider]

Originally Posted by dpl096

Once again ... excellent pick up and tutorial !!
Have these been added to the cross reference sticky?

Thanks for the kind words, and the reminder. I have added this thread to the RX3 Tech Sticky, under the Maintenance subheading.

http://www.chinariders.net/showthread.php?t=14228

[Weldangrind]

Originally Posted by SpudRider

I needed to cut the outer race with my dremel tool in order to remove it from the hub.

God Bless Dr. Emel. He makes a fine tool.

[SpudRider]

Originally Posted by Weldangrind

God Bless Dr. Emel. He makes a fine tool.

Indeed, he does make a very fine and useful tool.

[Rodtheviking]

Found these. If you have or use Mc-Master Carr

http://www.mcmaster.com/#standard-ba...rings/=11zcbzn

look under 6202 2rs and Premium Bearings

tighter tolerance

And hello.. new here.

[2LZ]

Spud, question. Do you use a power washer when you do get around to washing your bike? Since the advent of the power washer, in the past I've seen some wheel bearing failures and goose neck issues with my buddies who use them to wash their motocross bikes after muddy tracks. Seems the pressure blows the water right past the little axle seals. Just a thought.

[SpudRider]

Originally Posted by 2LZ

Spud, question. Do you use a power washer when you do get around to washing your bike? Since the advent of the power washer, in the past I've seen some wheel bearing failures and goose neck issues with my buddies who use them to wash their motocross bikes after muddy tracks. Seems the pressure blows the water right past the little axle seals. Just a thought.

No, I have never used a power washer on any of my motorcycles. I always use my garden hose.

Thanks for posting the caveat.

[SpudRider]

Originally Posted by Rodtheviking

Found these. If you have or use Mc-Master Carr

http://www.mcmaster.com/#standard-ba...rings/=11zcbzn

look under 6202 2rs and Premium Bearings

tighter tolerance

And hello.. new here.

Welcome, and thanks for posting the link.

[dpl096]

So for a new bike being delivered in the next few months what's the consensus ........ replace the factory bearings or remove the factory bearings and repack them with plenty of quality grease ?

[pyoungbl]

Originally Posted by dpl096

So for a new bike being delivered in the next few months what's the consensus ........ replace the factory bearings or remove the factory bearings and repack them with plenty of quality grease ?

The labor is the same. If you go to the trouble of taking the bearings out you may as well replace them with high quality ones...that you have packed with lots of grease.