Go Back   ChinaRiders Forums > Technical/Performance > Dual Sport/Enduro
Register FAQ Community Calendar Today's Posts Search
Reply
 
Thread Tools Search this Thread Display Modes
Old 12-09-2021, 05:46 PM   #61
China Rider 27   China Rider 27 is offline
 
Join Date: Dec 2018
Location: PNW
Posts: 984
OK I downloaded it but when zoomed the quality is pretty poor. He said it turned out to the right but looks to me like when you are sitting on it it turns out to the left which all different than a HAWK.


 
Reply With Quote
Old 12-09-2021, 05:52 PM   #62
tknj99   tknj99 is offline
 
Join Date: Oct 2020
Location: Central VA
Posts: 1,301
Quote:
Originally Posted by China Rider 27 View Post
OK I downloaded it but when zoomed the quality is pretty poor. He said it turned out to the right but looks to me like when you are sitting on it it turns out to the left which all different than a HAWK.
Well, it would turn to the right if your looking at the bike from the brake side.
On the Brozz, i have a Nibbi pod filter connected using a Nibbi manifold:
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

Filter:
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
__________________
2024 Templar 250
2021 Beta 500 RRS
2018 VStrom 1000 XT

Former China Bikes: Tao DBX1, Brozz 250, CSC RX4, Titan DLX, Templar X, Storm DLX 150


 
Reply With Quote
Old 12-09-2021, 11:11 PM   #63
Lee1991   Lee1991 is offline
 
Join Date: Dec 2021
Posts: 51
So if I did buy that pe28 and the other two nibbi attachments and it fits ,even if it is a slight pain, would I see a small performance boost compared to just running a vm26? Theoretically? ha


 
Reply With Quote
Old 12-10-2021, 07:28 AM   #64
tknj99   tknj99 is offline
 
Join Date: Oct 2020
Location: Central VA
Posts: 1,301
I'd imagine a very minimal gain.. The biggest gains you will get are by
1. removing the cat in the exhaust (cut/remove/weld - free/minimal cost) or replacing the header pipe altogether (can be found on Orion site): https://www.orionpowersports.com/sta...-249cc-engine/

2. adding a 4 degree timing key (Joe Henner sells them)
3. port/polish the head
__________________
2024 Templar 250
2021 Beta 500 RRS
2018 VStrom 1000 XT

Former China Bikes: Tao DBX1, Brozz 250, CSC RX4, Titan DLX, Templar X, Storm DLX 150


 
Reply With Quote
Old 12-10-2021, 11:13 AM   #65
Lee1991   Lee1991 is offline
 
Join Date: Dec 2021
Posts: 51
ok sounds good. i have added all that stuff to my various carts.

KP mentioned a boost bottle in a post in this thread a bit ago.... what is that and what are the benefits?

thanks for helping a newbie


 
Reply With Quote
Old 12-14-2021, 01:51 AM   #66
HEADL355 NINJA   HEADL355 NINJA is offline
 
Join Date: Dec 2021
Posts: 1
Hello, I just got my DB-X34 today excited. For mods to increase the hp I'm going to remove the cat. Not sure of I really want to do the 4 degree timing not sure if I need it for wat I'm using it for. I plan to take it on trails and dunes mostly. Any suggestions other than those?


 
Reply With Quote
Old 12-14-2021, 08:20 AM   #67
severely   severely is offline
 
Join Date: Oct 2021
Location: odessa MO; donna TX
Posts: 152
Quote:
Originally Posted by HEADL355 NINJA View Post
Hello, I just got my DB-X34 today excited. For mods to increase the hp I'm going to remove the cat. Not sure of I really want to do the 4 degree timing not sure if I need it for wat I'm using it for. I plan to take it on trails and dunes mostly. Any suggestions other than those?
Congratulations on your new purchase. There is a ton of information here just by re-reading the first few pages. For example, tknj99 talks about a CDI unit to install instead of the offset key and carb jetting to name a couple. I'd also recommend the disassembly and lubrication suggestions on other links. Good luck, let us know how you and your bike work out.


 
Reply With Quote
Old 12-15-2021, 03:45 PM   #68
Lee1991   Lee1991 is offline
 
Join Date: Dec 2021
Posts: 51
Does anyone know of any replacement plastics that fit these bikes?


 
Reply With Quote
Old 12-15-2021, 04:08 PM   #69
tknj99   tknj99 is offline
 
Join Date: Oct 2020
Location: Central VA
Posts: 1,301
https://www.chinariders.net/showthread.php?t=27109

or

https://www.orionpowersports.com/com...250-dirt-bike/
__________________
2024 Templar 250
2021 Beta 500 RRS
2018 VStrom 1000 XT

Former China Bikes: Tao DBX1, Brozz 250, CSC RX4, Titan DLX, Templar X, Storm DLX 150


 
Reply With Quote
Old 12-26-2021, 09:23 PM   #70
Howlan   Howlan is offline
 
Join Date: Dec 2021
Location: Wilson, North Carolina
Posts: 1
Great thread and details/info on the XPro Titan! Thanks everyone and especially tknj99 and Plump K .


Just got one delivered and doing the assembly now, this thread has helped a lot. Look forward to learning more and getting some time on it :-).


Thanks again, Howard in NC



Last edited by Howlan; 01-04-2022 at 08:01 PM.
 
Reply With Quote
Old 12-27-2021, 03:39 AM   #71
Thumper   Thumper is online now
 
Thumper's Avatar
 
Join Date: Feb 2021
Location: Kansas City
Posts: 2,733
Quote:
Originally Posted by tknj99 View Post
Went on a longer ride yesterday, about 30 miles.. a mix of street, gravel and a dirt trail.
Overall, she is performing great. The 30+ pounds of weight loss compared to the Brozz makes itself easily known. On the dirt trail there is a very steep and long down hill that i went on and if it weren't for the shipping oil that made its way to the rear brake, it was fine.. going up the hill was very fun, trucked up in first gear very easily with plenty of power on tap. As im limiting the revs to 6k at this time, there will be more to be had once i pass the 500mi mark and start opening her up.
With regards to the carb, I will probably swap to the VM26 and run a 100 main (i believe stock is 95) and center the clip on the needle.
You can mod the stock carb easily by cutting grooves into the bolt heads and change the main but the needle wont be adjustable (assuming same carb as the Brozz PZ30)
Also, to update regarding the damages, PSM responded back and claim that they dont have replacement parts on hand and offered $30 and i accepted.
Your complete write up is useful. THANKS!

The XPro does seem to be a good choice right now, especially for that engine.
A full size 21" front wheel is nice. My Bashan Storm has a 19" front wheel, which limits tire choices a bit, and it won't clear larger objects as easily as your XPro. The Storm does have a plush seat though!

Your carb plans sound perfect for my Storm as well. I live below 1000 feet and the jetting and needle height settings you describe are a good place to start. I will carve out the converter and modify the airbox to increase flow too. That and the carb swap may be sufficient to add 4-5hp without making it loud.

Have fun!


 
Reply With Quote
Old 01-04-2022, 12:46 PM   #72
tknj99   tknj99 is offline
 
Join Date: Oct 2020
Location: Central VA
Posts: 1,301
Update: did the 500 mile oil change and now able to wind her out.. it seems that top speed (for my 185 weight) around 63 or so mph with 60mph being comfortable. This translates to around 55mph with the stock gearing which is fine for me as i like its behavior off-road as is.
Also with regard to the VM26, i just ordered a Mikuni jet kit as i want to replace the 20 pilot it came with and install a 25 pilot as i feel a hesitation at slightest of throttle inputs. I may also back the 120 main down to a 115 as it bogged a bit during top speed when twisting out the throttle.
__________________
2024 Templar 250
2021 Beta 500 RRS
2018 VStrom 1000 XT

Former China Bikes: Tao DBX1, Brozz 250, CSC RX4, Titan DLX, Templar X, Storm DLX 150


 
Reply With Quote
Old 01-07-2022, 08:40 AM   #73
ghostdancing   ghostdancing is offline
 
Join Date: Jul 2021
Posts: 62
Is there any cheaper option for a stainless header for the 223 ohc motor? I saw something on aliexpress but it has that "powerbomb" thing and i guess there is the catalityc filter in it..correct?


 
Reply With Quote
Old 01-14-2022, 11:46 AM   #74
Lee1991   Lee1991 is offline
 
Join Date: Dec 2021
Posts: 51
Just ordered mine! hopefully ill have some updates and photos late next week.


 
Reply With Quote
Old 01-14-2022, 12:03 PM   #75
tknj99   tknj99 is offline
 
Join Date: Oct 2020
Location: Central VA
Posts: 1,301
Quote:
Originally Posted by ghostdancing View Post
Is there any cheaper option for a stainless header for the 223 ohc motor? I saw something on aliexpress but it has that "powerbomb" thing and i guess there is the catalityc filter in it..correct?
Unfortunately none of the Ebay/Amazon pipes that work for the Brozz/Hawk/TBR CG engine will work on the Titan with the 229cc CB engine.
The options are:
1. cut/remove/weld stock pipe to remove cat
2. buy this header off Orion: https://www.orionpowersports.com/sta...-223cc-engine/
__________________
2024 Templar 250
2021 Beta 500 RRS
2018 VStrom 1000 XT

Former China Bikes: Tao DBX1, Brozz 250, CSC RX4, Titan DLX, Templar X, Storm DLX 150


 
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:38 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.