egr valve

darkiller888 · 04-20-2007, 01:59 PM

i took the hoses off my bike and it seems to run better. the hose that connects to the side of the motor , i started it up without it being plugged and it runs through the exaust but i crimped the tube and put it back on and it definetly has a lot more balls the throttle seems to be a lot touchier and i will probably get some more compression on my rds-200.

liverchip · 04-20-2007, 02:05 PM

Yes...most of us have disabled or removed that system with good results.

fishman · 07-23-2007, 11:54 AM

can any one tell me if taking this stuff of will actually help and do i leave the crankcase breather on ,but take everything else off

ejcycles · 07-23-2007, 12:11 PM

Leave the crankcase breather alone! Do Not plug it or remove it.

fishman · 07-23-2007, 01:06 PM

will i need to change the needle/clip height or carb setting ??? cause the burn on the plug was a perfect light tan before????I also cannot get any play in the clutch cable ,both adjustments are bottomed out ,bike is brand new will it get better.????

ejcycles · 07-24-2007, 09:25 AM

fishman
What make bike do you have?
Yes you will need to re-adjust your carburetor, but I can't tell you what to re-adjust it to because I don't know where you live and what your altitude is.
The clutch cable you have on the bike may be too short that's why you don't have any free-play. Will it get better... yes as the clutch plates wear but it may take quite a while. Your best bet is to get a longer clutch cable, but since I don't know what ends are on yours I can't help there would need pics.

fishman · 07-24-2007, 12:19 PM

i have the orion or viva 250 dirtbike ,and now the seals on the upside down forks are leaking badly and of course no help from the internet site i bought it ,except to sell me new forks or sell me fork seals which are backordered from china, Bike is 3 days old.

frostbite · 07-24-2007, 02:45 PM

Quote:

i have the orion or viva 250 dirtbike ,and now the seals on the upside down forks are leaking badly and of course no help from the internet site i bought it ,except to sell me new forks or sell me fork seals which are backordered from china, Bike is 3 days old.

This post has nothing to do with the current discussion thread. Please limit discussion to the topic at hand (EGR valve) or start a new thread.

Thanks,

04-20-2007, 01:59 PM	#1
darkiller888 Join Date: Mar 2007 Location: massenaNY Posts: 25	egr valve i took the hoses off my bike and it seems to run better. the hose that connects to the side of the motor , i started it up without it being plugged and it runs through the exaust but i crimped the tube and put it back on and it definetly has a lot more balls the throttle seems to be a lot touchier and i will probably get some more compression on my rds-200.
	0

04-20-2007, 02:05 PM	#2
liverchip Join Date: Nov 2006 Location: Mystery Spot Posts: 1,223	Yes...most of us have disabled or removed that system with good results. __________________ 2009 XR650L Big Red Pig Tusk bar risers 2007 X-Moto(Jetmoto) GY250 --mods--- 15/40 sprockets UNI Pod Filter 2007 Shineray TMS 200XYi--Betsy Betsy Mods:______________________ Acerbis DHH headlight FMF Powercore pipe Uni Pod Filter
	0

07-23-2007, 11:54 AM	#3
fishman Join Date: Jul 2007 Posts: 11	emissions can any one tell me if taking this stuff of will actually help and do i leave the crankcase breather on ,but take everything else off
	0

07-23-2007, 12:11 PM	#4
ejcycles Join Date: Oct 2006 Location: 11481 State Route 44 Mantua, Ohio 44255 Posts: 1,112	Leave the crankcase breather alone! Do Not plug it or remove it. __________________ Thanks, Bruce @ Endless Journey Cycles "Phone Calls Only" ~330-274-0098~ Hours: Tue.-Fri. 10:00-6:00 Sat. 10:00-4:00 EST. Dealer for: Lifan, Crossrunner ATVs. http://www.endlessjourneycycles.net
	0

07-23-2007, 01:06 PM	#5
fishman Join Date: Jul 2007 Posts: 11	egr emissions will i need to change the needle/clip height or carb setting ??? cause the burn on the plug was a perfect light tan before????I also cannot get any play in the clutch cable ,both adjustments are bottomed out ,bike is brand new will it get better.????
	0

07-24-2007, 09:25 AM	#6
ejcycles Join Date: Oct 2006 Location: 11481 State Route 44 Mantua, Ohio 44255 Posts: 1,112	fishman What make bike do you have? Yes you will need to re-adjust your carburetor, but I can't tell you what to re-adjust it to because I don't know where you live and what your altitude is. The clutch cable you have on the bike may be too short that's why you don't have any free-play. Will it get better... yes as the clutch plates wear but it may take quite a while. Your best bet is to get a longer clutch cable, but since I don't know what ends are on yours I can't help there would need pics. __________________ Thanks, Bruce @ Endless Journey Cycles "Phone Calls Only" ~330-274-0098~ Hours: Tue.-Fri. 10:00-6:00 Sat. 10:00-4:00 EST. Dealer for: Lifan, Crossrunner ATVs. http://www.endlessjourneycycles.net
	0

07-24-2007, 12:19 PM	#7
fishman Join Date: Jul 2007 Posts: 11	egr i have the orion or viva 250 dirtbike ,and now the seals on the upside down forks are leaking badly and of course no help from the internet site i bought it ,except to sell me new forks or sell me fork seals which are backordered from china, Bike is 3 days old.
	0