Hawk or other 229cc engine based enduro setup database - Page 2

rvl8rida · 05-19-2017, 11:51 AM

so the fact that i have mine on the lowest notch with a washer under it probably means im too rich? haha

Megadan · 05-19-2017, 11:59 AM

Quote:

Originally Posted by rvl8rida

so the fact that i have mine on the lowest notch with a washer under it probably means im too rich? haha

I think that says you probably want to consider going up a size or two on the main jet.

Ariel Red Hunter · 05-19-2017, 01:13 PM

Quote:

Originally Posted by Megadan

I think that says you probably want to consider going up a size or two on the main jet.

I agree!!...ARH

Wancsta · 07-05-2017, 08:27 AM

Bike: 2015 RPS Hawk

Elevation: 1100ft

Carb: PZ30

Jet sizes: 110 main, stock pilot

Needle setting: 2 shims

Pilot screw turns: 2.25

Relevant mods: Air box mod, foam filter element, eBay exhaust, 17t front, 47t rear, shinko 705'

Top speed: 67(gps) flat out, can cruise at 60 now

RogerWFarrier · 07-07-2017, 11:27 PM

Quote:

Originally Posted by JerryHawk250

The stock carbs don't have the grooves so we have to shim it.

The TT runs a Keima carb from the factory and it does have the slotted needle so it's just a matter of moving the clip to change needle position.

Sullybiker · 07-08-2017, 08:10 AM

TT250. Altitude 1000ft.

VM26 Chikuni, stock exhaust and airbox.

Pilot: 27
Main: 105

Mixture screw 1.75 turns out.

jimwildman · 07-11-2017, 06:36 AM

Quote:

Originally Posted by Ariel Red Hunter

I didn't know that an Ariel Square Four was wierdo stuff, but I am always willing to be educated. Sorry you didn't find any useful stuff on Hawk Talk...ARH

so now your gonna ruin this thread too?

Ariel Red Hunter · 07-11-2017, 09:43 AM

Quote:

Originally Posted by jimwildman

so now your gonna ruin this thread too?

If you don't like what I write - don't read it...ARH

Megadan · 07-16-2017, 02:49 AM

Revised.
Bike: 2017 Hawk

Elevation: 1100ft

Carb: Mikuni VM26 "30mm" Clone

Jet sizes: Genuine Mikuni Jets - 27.5 Pilot. 117.5 Main, factory needle and needle jet.

Needle setting: 4th notch down from the top. (center also works, but I chose the "fatter" option)

Pilot screw turns: 1 1/4 (still needs a little fine tuning but close)

Relevant mods: Sprockets - 17 front, 43 rear. Uni pod filter, Ebay exhaust. Denso iridium plug, NGK XD05F plug cap with resistor removed and shortened plug wire.

Top speed: 70mph GPS on flat ground wth no wind.

Megadan · 07-29-2017, 10:59 PM

Bumping this thread so people are aware of it. Don't be afraid to post examples on here for others. With so many Mikuni clones out there, I think there could be a few more examples on here.

silva · 08-01-2017, 10:06 PM

Bike: 2016 hawk. .
Elevation: 6400
Carb: PZ30 98 main/stock pilot. Relevant mods: k&n air filter/box mod .Ebay exhaust. NGK BR8EIX plug.
Rotella T6. Valve cover oil cooler from mjstef.
JT non o-ring chain. 17/40 gearing. shinko 705 (rear) Top speed:75 mph, (gps)

pistolclass · 08-01-2017, 10:54 PM

2016 hawk:

$30 Makuni (fake) VM26
110 main
20 pilot
2 turns out
needle set on fattest setting.
Stock Air box
Stock exhaust
63 mph top speed
15 front
50 rear
set both intake and Exhaust to 0.05 mm

matt's digital cluster
MSR shifter
burrito tube

Hawk starts right up and there is no flat spot in the RPM range. Really happy with this set up.

KingPrimusIII · 08-06-2017, 09:08 PM

Bike: 2015 Hawk

Elevation:240'

Carb: Factory

Jet sizes: 110 Kehein main, factory pilot

Needle setting: 2 custom washers

Pilot screw turns: 1 1/2

Relevant mods: Airbox mod, NGK plug

Top speed: 57mph, gps confirmed

XDoubleXA · 09-13-2017, 02:13 PM

UPDATED!

Bike: Bashan Shark 250

Elevation: 981 ft

Carb: Stock Keihin

Jet sizes: Slow 35, Main 120

Needle setting: Clip last notch down.

Pilot screw turns: 1 3/4

Relevant mods: Ebay CRF230 Exhaust, After market needle, Uni Pod filter.

Top speed: 70MPH (GPS) Top speed. Likes to cruise around 55-60

Sprockets: 17T front, and 45T Rear.

wamey · 09-26-2018, 09:43 AM

Bike: 2017 Hawk

Elevation: 870ft

Carb: Mikuni VM26 Clone

Jet sizes: Genuine Mikuni Jets - 28 Pilot. 112.5 Main. Factory needle.

Needle setting: middle notch

Pilot screw turns: 1 1/2

Relevant mods: Sprockets - 17 front, 47 rear. Battlax BT45 tires. Motocheez airbox mod. PCV installed in crankcase breather tube. Front fork brace to help with front end speed wobbles.

Top speed: 68mph flat out (no wind, flat road)

07-16-2017, 02:49 AM	#24
Megadan Join Date: Apr 2017 Location: Omaha, NE Posts: 7,986	Revised. Bike: 2017 Hawk Elevation: 1100ft Carb: Mikuni VM26 "30mm" Clone Jet sizes: Genuine Mikuni Jets - 27.5 Pilot. 117.5 Main, factory needle and needle jet. Needle setting: 4th notch down from the top. (center also works, but I chose the "fatter" option) Pilot screw turns: 1 1/4 (still needs a little fine tuning but close) Relevant mods: Sprockets - 17 front, 43 rear. Uni pod filter, Ebay exhaust. Denso iridium plug, NGK XD05F plug cap with resistor removed and shortened plug wire. Top speed: 70mph GPS on flat ground wth no wind. __________________ Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124 Last edited by Megadan; 04-10-2019 at 11:11 PM.
	0

07-29-2017, 10:59 PM	#25
Megadan Join Date: Apr 2017 Location: Omaha, NE Posts: 7,986	Bumping this thread so people are aware of it. Don't be afraid to post examples on here for others. With so many Mikuni clones out there, I think there could be a few more examples on here. __________________ Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124
	0

08-01-2017, 10:06 PM	#26
silva Join Date: Jan 2017 Posts: 37	hawk 250 Bike: 2016 hawk. . Elevation: 6400 Carb: PZ30 98 main/stock pilot. Relevant mods: k&n air filter/box mod .Ebay exhaust. NGK BR8EIX plug. Rotella T6. Valve cover oil cooler from mjstef. JT non o-ring chain. 17/40 gearing. shinko 705 (rear) Top speed:75 mph, (gps) Last edited by silva; 08-01-2017 at 11:58 PM.
	1

08-06-2017, 09:08 PM	#28
KingPrimusIII Join Date: Mar 2017 Location: Beautiful Upstate NY Posts: 65	Bike: 2015 Hawk Elevation:240' Carb: Factory Jet sizes: 110 Kehein main, factory pilot Needle setting: 2 custom washers Pilot screw turns: 1 1/2 Relevant mods: Airbox mod, NGK plug Top speed: 57mph, gps confirmed __________________ "You think life is crazy now? Just wait until the internet arrives!" -Albert Einstein
	0

09-13-2017, 02:13 PM	#29
XDoubleXA Join Date: Apr 2017 Location: Ohio Posts: 89	UPDATED! Bike: Bashan Shark 250 Elevation: 981 ft Carb: Stock Keihin Jet sizes: Slow 35, Main 120 Needle setting: Clip last notch down. Pilot screw turns: 1 3/4 Relevant mods: Ebay CRF230 Exhaust, After market needle, Uni Pod filter. Top speed: 70MPH (GPS) Top speed. Likes to cruise around 55-60 Sprockets: 17T front, and 45T Rear. __________________ Bashan Shark, Keihen PZ30 Carb, Pilot 40, Main 120, Uni Filter, Exhaust, MSR Shifter, and some stickers.
	0

05-19-2017, 11:51 AM	#16
rvl8rida Join Date: Apr 2017 Posts: 27	so the fact that i have mine on the lowest notch with a washer under it probably means im too rich? haha
	0

07-05-2017, 08:27 AM	#19
Wancsta Join Date: May 2017 Posts: 24	Bike: 2015 RPS Hawk Elevation: 1100ft Carb: PZ30 Jet sizes: 110 main, stock pilot Needle setting: 2 shims Pilot screw turns: 2.25 Relevant mods: Air box mod, foam filter element, eBay exhaust, 17t front, 47t rear, shinko 705' Top speed: 67(gps) flat out, can cruise at 60 now
	0

07-08-2017, 08:10 AM	#21
Sullybiker Join Date: Dec 2016 Location: Western PA Posts: 363	TT250. Altitude 1000ft. VM26 Chikuni, stock exhaust and airbox. Pilot: 27 Main: 105 Mixture screw 1.75 turns out.
	0

08-01-2017, 10:54 PM	#27
pistolclass Join Date: Oct 2015 Location: connecticut Posts: 978	2016 hawk: $30 Makuni (fake) VM26 110 main 20 pilot 2 turns out needle set on fattest setting. Stock Air box Stock exhaust 63 mph top speed 15 front 50 rear set both intake and Exhaust to 0.05 mm matt's digital cluster MSR shifter burrito tube Hawk starts right up and there is no flat spot in the RPM range. Really happy with this set up.
	0

09-26-2018, 09:43 AM	#30
wamey Join Date: Jun 2017 Location: Madison, WI Posts: 96	Bike: 2017 Hawk Elevation: 870ft Carb: Mikuni VM26 Clone Jet sizes: Genuine Mikuni Jets - 28 Pilot. 112.5 Main. Factory needle. Needle setting: middle notch Pilot screw turns: 1 1/2 Relevant mods: Sprockets - 17 front, 47 rear. Battlax BT45 tires. Motocheez airbox mod. PCV installed in crankcase breather tube. Front fork brace to help with front end speed wobbles. Top speed: 68mph flat out (no wind, flat road)
	0