|
|
05-22-2019, 07:07 AM
|
#1 |
Join Date: Jun 2016
Location: Hell
Posts: 2,408
|
CSC TT250 guy are they much into mods for PZ30B carb?
I've looked into the cable for that style of switch gear but the solution I got is just OK and needs fiddling to work etc. Really it needs a correct style cable with the elbow and fitting into the switch gear correctly and correct length inner cable. Worst case could be different switch gear without the A1 A2 but that kinda isn't the nicest way. I managed to find 'good enough" solution with some DIY required to make it work "fine" or best I can without the actual bike (Used RX3 switch gear to test fit) |
|
|
05-26-2019, 01:51 PM
|
#2 |
|
Join Date: Dec 2015
Location: CO
Posts: 1,525
|
"Dual Cable PZ30B Pumper Carb" does not fit on the Bashan WILL 200 or other similar framed bikes
I'm a sad Panda today  Anyone in my area need a PZ30B let me know... I never actually used/filled the PZ30B with gas but I did clean and lube it up (MMO and Neutra 131 mix) getting it ready for service on my Bashan... and I quickly found that the "pumper cable mounting bracket" hits the right side frame no matter what you do 
__________________
"Think as you like... but this self proclaimed Professor is always right" - Buckshot "You never know what someone is hiding beneath their smile..." - NinjaTom - R.I.P. |
|
|
|
05-26-2019, 05:07 PM
|
#3 |
Join Date: Apr 2017
Location: Omaha, NE
Posts: 8,008
|
Take pictures of the jets and post them up.
__________________
Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124 |
|
|
|
05-27-2019, 12:53 AM
|
#5 |
|
Join Date: Apr 2017
Location: Omaha, NE
Posts: 8,008
|
That looks like half of a n424 or 99103 jet. Like the emulsion tube on the end is missing.
__________________
Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124 |
|
|
|
05-27-2019, 09:43 AM
|
#6 |
|
Join Date: Dec 2018
Location: PNW
Posts: 982
|
Here is better shot of the internal engagement. There is a tapered brass plug the jet seats on. The jet itself is concave so it forms a seal. This N424 Keihin jet looks similar but says 4.5 mm and my jet measures 4.8 on the body and 5 mm on thread. Emailing the seller so see what they have to say.
Here is link to similar Keihin N424. http://www.keihin-fcr.com/index.php?...roduct_id=1815 |
|
|
|
05-27-2019, 08:36 PM
|
#7 |
|
Join Date: Jun 2016
Location: Hell
Posts: 2,408
|
That is the same as my PZ30B and what is in my first tune kits. I am 99% sure.
Best I know there are 3 types of pilot jets in the Chinese clone PZ30 Keihin based carbs (1 of each is in the first tune kit I sell, also used in the PZ30B I sell) https://www.ebay.com/itm/303169447550 Last edited by NzBrakelathes; 05-28-2019 at 04:40 AM. |
|
|
|
06-09-2019, 10:25 AM
|
#8 |
|
Join Date: May 2019
Location: Maine
Posts: 111
|
It looks like the main jet is still screwed into the emulsion tube, would be tough for anyone to tell what it is - Unless that is really one piece
|
|
|
|
06-09-2019, 11:13 AM
|
#9 | |
|
Join Date: May 2019
Posts: 47
|
Quote:
|
|
|
|
|
06-11-2019, 06:25 AM
|
#10 | |
|
Join Date: Jun 2016
Location: Hell
Posts: 2,408
|
Quote:
I should be posting them from CT USA Today or so |
|
|
|
|
06-11-2019, 03:12 PM
|
#11 | |
|
Join Date: May 2019
Posts: 47
|
Quote:
|
|
|
|
|
06-11-2019, 07:20 PM
|
#12 | |
|
Join Date: Jun 2016
Location: Hell
Posts: 2,408
|
Quote:
I have: Pumper carb set with all options. Carb air screw tool Valve adj tool set Lock set for either hawk or TBR7 which just needs a plug change. Couple large rear racks A few more first tune kits coming with me wife next week I’m a bit limited while here or faster postage |
|
|
|
|
06-11-2019, 09:45 PM
|
#13 |
|
Join Date: May 2019
Location: Port Huron, Michigan
Posts: 637
|
Got my pz30b a few days ago from nzbrakelathes, need to get it on my storm soon. Bikes stock right now, any advice on where to start with jetting? Might do an exhaust in the fall, right now what little time I have is going to wrenching on the storm and my vtx so I can hopefully ride them soon.
|
|
|
|
06-11-2019, 10:02 PM
|
#14 | |
|
Join Date: Jun 2016
Location: Hell
Posts: 2,408
|
Quote:
That’s the same as hawk first tune I’d suggest that be ok as a starting point etc |
|
|
|
|
06-11-2019, 10:04 PM
|
#15 | |
|
Join Date: Apr 2017
Location: Omaha, NE
Posts: 8,008
|
Quote:
__________________
Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124 |
|
|
|
|
|
|
 |
|
|
Hybrid Mode
