06-05-2017, 12:11 AM
|
#3 |
Join Date: Feb 2017
Location: Holiday, Florida
Posts: 672
|
I think I would go through eBay and get Honda studs!
__________________
Dan-O -2018 Tao Tao HellCat - DOA -2016 Hawk 250 - Kitty Hawk - eBay exhaust, Mikuni carb(120 main/30 Pilot), airbox mod with K&N filter, digital cluster, total LEDs, 17/45 sprockets, RK chain, Shinko 244 tires, trunk, aftermarket levers, burrito tube, skid plate, Sargent Cycle Seat... -2003 HD Sportster 100th Anniversary -1999 Buell X-1 Lightning - Race kit, Buell Seat |
|
|
06-05-2017, 09:10 PM
|
#4 |
Join Date: Sep 2015
Location: East Central Hellinois
Posts: 1,344
|
If you are the least bit uncomfortable with the Chinese studs by all means switch them out with the Honda studs.
__________________
************************************************** *** " Time you enjoy wasting, is not wasted." - John Lennon  “I predict future happiness for Americans, if they can prevent the government from wasting the labors of the people under the pretense of taking care of them.” ― Thomas Jefferson "If you don't know where you're going any road will take you there" ....George Harrison song |
|
|
|
06-08-2017, 06:19 PM
|
#6 | |
|
Join Date: May 2016
Posts: 583
|
Quote:
|
|
|
|
|
06-08-2017, 08:10 PM
|
#8 | |
|
Join Date: May 2016
Posts: 583
|
Quote:
|
|
|
|
|
06-08-2017, 09:15 PM
|
#9 |
Join Date: Apr 2017
Location: Omaha, NE
Posts: 7,953
|
Personally, given what I have discovered with the rear sprocket, I would avoid riding the bike until you replace the studs. If that sprocket comes free, it can be a huge safety hazard. Best case scenario, you loose drive power and get stuck pushing your bike. Worst case, the rear wheel gets locked up, you destroy a bunch of parts on the bike, and it causes you to crash and get hurt.
__________________
2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2010 VFR1200F - http://chinariders.net/showthread.php?t=20708 |
|
|
|
06-09-2017, 11:42 AM
|
#10 | |
|
Join Date: Feb 2016
Location: Kingston, NY
Posts: 66
|
One of the other guys in a separate thread mentioned he walked into a Honda Bike dealer and they found a part that matched up for him. The part number hand written on the bag was 90128-312-000 ... That brings up a Honda SL350 when searching the internet, but those appear to be discontinued. A few show up on Ebay for them, but hopefully your Honda dealer has something for you that fits. If you find something else, please share it with us!
Here is his original post in this thread http://chinariders.net/showthread.php?t=19265&page=2 Quote:
|
|
|
|
|
06-09-2017, 01:46 PM
|
#11 |
|
Join Date: Apr 2017
Location: Omaha, NE
Posts: 7,953
|
It brings up the SL350 up to about 1972, where it is replaced with a different part number, most likely a small revision to the same part.
__________________
2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2010 VFR1200F - http://chinariders.net/showthread.php?t=20708 |
|
|
|
|
|
 |
|
|
Linear Mode
