Took a plunge... trying a PP LXR250 EFI - Page 3

2LZ · 04-14-2017, 11:49 AM

I didn't catch it here but yes, that's the exact motor and cooling system that's in the RX3. Not the "ZS" on the engine number, It's a Zong!
I believe this bike is advertised with more HP though....and yes, good luck getting at those valves. The intake on the RX3 isn't bad....the exhaust on the other hand....

Sweet ride!

ben2go · 04-14-2017, 09:36 PM

That's a real nice China bike and the included tool kit and EFI diagnosis kit is excellent. Can you confirm the advertised seat height is 37 inches? That's KTM territory.

ChondaChondaChonda · 04-14-2017, 10:51 PM

Quote:

Originally Posted by ben2go

That's a real nice China bike and the included tool kit and EFI diagnosis kit is excellent. Can you confirm the advertised seat height is 37 inches? That's KTM territory.

Yes, it is. I'm beginning to think that the frame and geometry are "KTM inspired". The tank, exhaust and swing arm are very 2006-2010 KTM 250 looking.

Hard to get 12 inches of travel at both ends without the seat getting higher. I'm with you on it being a little too tall. I may drop the forks in the triples and put a lowering link on it after getting the rear suspension dialed. I'm a fat kid with short legs!!

The good thing is the springs are so soft that it drops to where I can flat foot it with a 32" inseam.

ChondaChondaChonda · 04-14-2017, 10:53 PM

I forgot these earlier:

A few shots of the battery and air filter. The filter comes out the side panel. 2 screws to get it out.

You can also see the starter solenoid and CDI.

ChondaChondaChonda · 04-14-2017, 10:57 PM

Oil was dumped warm after riding it home from inspection station. Oil looked beautiful and fresh. Almost a shame to dump it, but better safe than sorry. The oil filter looked pristine. I thought I had a replacement, but it was the wrong filter.

Here's how the magnet looked:

pete · 04-21-2017, 02:54 AM

Quote:

Originally Posted by ChondaChondaChonda

Oil was dumped warm after riding it home from inspection station. Oil looked beautiful and fresh. Almost a shame to dump it, but better safe than sorry. The oil filter looked pristine. I thought I had a replacement, but it was the wrong filter.

Here's how the magnet looked:

Was the drain plug a wee bit on the tight side ?

..

pete · 04-14-2017, 11:05 PM

Quote:

Originally Posted by ChondaChondaChonda

Yes, it is. I'm beginning to think that the frame and geometry are "KTM inspired". The tank, exhaust and swing arm are very 2006-2010 KTM 250 looking.

Hard to get 12 inches of travel at both ends without the seat getting higher. I'm with you on it being a little too tall. I may drop the forks in the triples and put a lowering link on it after getting the rear suspension dialed. I'm a fat kid with short legs!!

The good thing is the springs are so soft that it drops to where I can flat foot it with a 32" inseam.

With 300mm wheel travel it will drop 100mm when seated if you set the sags...

...

ChondaChondaChonda · 04-14-2017, 11:15 PM

Quote:

Originally Posted by pete

With 300mm wheel travel it will drop 100mm when seated if you set the sags...

...

Yes, it *feels* smaller than the specs as is. I haven't had time to mess with sag. I weigh enough and have had enough bikes to know that I will need a stiffer rear spring. Working on a solution from my "box 'o springs" in the garage; I have quite a collection from over the years.

As is, it is very good on the street.

humanbeing · 04-14-2017, 10:59 PM

You may already know it's a Kayo. K6 had the same ECU https://v.qq.com/x/page/o0157yyhyyq.html
If had Wechat http://siyigenealogy.proboards.com/t...scrollTo=18601 visits

& grab the latest info

ChondaChondaChonda · 04-14-2017, 11:06 PM

Quote:

Originally Posted by humanbeing

You may already know it's a Kayo. K6 had the same ECU
https://v.qq.com/x/page/o0157yyhyyq.html

Yes. That looks like the same bike with some minor differences.

I wish I knew what they were saying in that Video!

ChondaChondaChonda · 04-17-2017, 05:33 PM

Well, the Pitster Pro LXR250 is now plated.

Turns out the inspection wasn't even necessary... because it was new. Better safe than sorry. PLUS, it was an excuse to ride. Now that I'm legal I need to do some explorin'.

MOTOXtreme · 04-17-2017, 06:53 PM

Quote:

Originally Posted by ChondaChondaChonda

Well, the Pitster Pro LXR250 is now plated.

Turns out the inspection wasn't even necessary... because it was new. Better safe than sorry. PLUS, it was an excuse to ride. Now that I'm legal I need to do some explorin'.

Awesome. And Explorin you will do I'm sure. Thats the main reason I got mine..>So when I say "hmmm, wonder where that road goes...."

BlackBike · 04-17-2017, 09:03 PM

Great feeling with that plate !!

dpl096 · 04-17-2017, 09:06 PM

Exactly...now that it's plated you wanna take it off the road and to where no plates are needed...just the desire to see what around that next bend in the trail or treeline....freedom!

Quote:

Originally Posted by ChondaChondaChonda

Well, the Pitster Pro LXR250 is now plated.

Turns out the inspection wasn't even necessary... because it was new. Better safe than sorry. PLUS, it was an excuse to ride. Now that I'm legal I need to do some explorin'.

BlackBike · 04-17-2017, 10:59 PM

Quote:

Originally Posted by dpl096

Exactly...now that it's plated you wanna take it off the road and to where no plates are needed...just the desire to see what around that next bend in the trail or treeline....freedom!

Yeah right , here is the example (freedom) of what I find at the end of the county road...keep out

04-14-2017, 11:49 AM	#1
2LZ Join Date: Mar 2010 Location: Volcano, Ca Posts: 7,085	I didn't catch it here but yes, that's the exact motor and cooling system that's in the RX3. Not the "ZS" on the engine number, It's a Zong! I believe this bike is advertised with more HP though....and yes, good luck getting at those valves. The intake on the RX3 isn't bad....the exhaust on the other hand.... Sweet ride! __________________ "Light a fire for a man, and you heat him for a day. Light a man on fire, and you heat him for the rest of his life." 2007 Suzuki DRZ400S (SM convert) 2009 Q Link XP 200 1967 BSA B25 250cc Starfire 2022 Royal Enfield Interceptor 650 2023 Royal Enfield Scram 411 1948 Royal Enfield Model G 350
	0

04-14-2017, 10:53 PM	#4
ChondaChondaChonda Join Date: Oct 2016 Posts: 547	I forgot these earlier: A few shots of the battery and air filter. The filter comes out the side panel. 2 screws to get it out. You can also see the starter solenoid and CDI. __________________ 1993 CR125 powered by Zongshen 223cc OHC 2̶0̶1̶6̶ ̶L̶X̶R̶ ̶2̶5̶0̶ ̶E̶F̶I̶ ̶ Sold 2018 GPX Moto FSE250R 1993 Fantic Key-Roo 250 Last edited by ChondaChondaChonda; 04-14-2017 at 10:54 PM. Reason: Added CDI info
	1

04-14-2017, 10:57 PM	#5
ChondaChondaChonda Join Date: Oct 2016 Posts: 547	First oil change at 25 miles... Oil was dumped warm after riding it home from inspection station. Oil looked beautiful and fresh. Almost a shame to dump it, but better safe than sorry. The oil filter looked pristine. I thought I had a replacement, but it was the wrong filter. Here's how the magnet looked: __________________ 1993 CR125 powered by Zongshen 223cc OHC 2̶0̶1̶6̶ ̶L̶X̶R̶ ̶2̶5̶0̶ ̶E̶F̶I̶ ̶ Sold 2018 GPX Moto FSE250R 1993 Fantic Key-Roo 250
	2

04-14-2017, 10:59 PM	#9
humanbeing Join Date: Mar 2008 Posts: 2,436	You may already know it's a Kayo. K6 had the same ECU https://v.qq.com/x/page/o0157yyhyyq.html If had Wechat http://siyigenealogy.proboards.com/t...scrollTo=18601 visits & grab the latest info __________________
	0

04-17-2017, 05:33 PM	#11
ChondaChondaChonda Join Date: Oct 2016 Posts: 547	Well, the Pitster Pro LXR250 is now plated. Turns out the inspection wasn't even necessary... because it was new. Better safe than sorry. PLUS, it was an excuse to ride. Now that I'm legal I need to do some explorin'. __________________ 1993 CR125 powered by Zongshen 223cc OHC 2̶0̶1̶6̶ ̶L̶X̶R̶ ̶2̶5̶0̶ ̶E̶F̶I̶ ̶ Sold 2018 GPX Moto FSE250R 1993 Fantic Key-Roo 250
	2

04-14-2017, 09:36 PM	#2
ben2go Join Date: Jun 2011 Posts: 1,335	That's a real nice China bike and the included tool kit and EFI diagnosis kit is excellent. Can you confirm the advertised seat height is 37 inches? That's KTM territory.
	1

04-17-2017, 09:03 PM	#13
BlackBike Join Date: Feb 2016 Location: George West, Texas Posts: 4,097	Great feeling with that plate !! __________________ ***************************************** 2015 Bashan"Blaze" BS250GY-31 (DB-07K-250) GONE 2017 Suzuki V Strom 650 XT "We are all born ignorant, but one must work hard to remain stupid." ~Benjamin Franklin~
	0