Vitacci Clash 200 EFI Scooter - Page 10

Mudflap · 05-27-2023, 11:08 AM

I pulled the fuel gauge sending unit/fuel pump to see if it was hanging up or could be adjusted but no joy. The ohm reading from the potentiometer was consistent throughout it's range of movement, and it moved freely. Couldn't bend the float rod enough to make a difference because doing so would make it hit the filter or the top of the tank. Range is 8.5 ohms to 87 ohms.

clash 168cc · 05-27-2023, 08:22 PM

Quote:

Originally Posted by Mudflap

I pulled the fuel gauge sending unit/fuel pump to see if it was hanging up or could be adjusted but no joy. The ohm reading from the potentiometer was consistent throughout it's range of movement, and it moved freely. Couldn't bend the float rod enough to make a difference because doing so would make it hit the filter or the top of the tank. Range is 8.5 ohms to 87 ohms.

My fuel gauge has started to wander up and down. Even 5 miles after a full tank it drops to 3 bars then 6 then 4. I just go by resetting the trip A when it's full. I'm going to run the tank down and see what miles it goes to empty. If the display goes out I'll use a dip stick later on. The display can't be cheap or easy to get and would have the same low quality if you bought a new one. You might see if the dealer can get you a new sending unit for it. Might not be too much.

Mudflap · 06-18-2023, 01:24 PM

About 3000 miles now and then rear tire is nearly worn out. I'll be installing the Michelin next week. No complaints about the original Seyoun tires in the handling department, they are soft and grippy.

Mikd · 06-28-2023, 02:28 PM

Have a Clash 200 on order. Fingers crossed its a decent little runabout. Glad this place is here for info as I like to tinker.

Mudflap · 06-28-2023, 02:57 PM

Quote:

Originally Posted by Mikd

Have a Clash 200 on order. Fingers crossed its a decent little runabout. Glad this place is here for info as I like to tinker.

Hope yours arrives without shipping damage. Chinese bikes are great for those who like to tinker. Parts are super cheap.

Mikd · 06-30-2023, 10:33 PM

Arrived today, packaging was clean. Hopefully assemble it tomorrow.

Mikd · 06-30-2023, 10:38 PM

Great looking scooter

Mikd · 07-02-2023, 04:54 PM

Question, has anyone experienced the electronic speedo not registering speed? Seems to happen about 1/3 of the time.

Mikd · 07-02-2023, 04:55 PM

Pic

clash 168cc · 07-02-2023, 06:24 PM

Check your connections. must be a speed sensor on the wheel somewhere. Mine is showing over actual speed between 3 to 7 mph like most of them. There's a wire going to the right side of the front axle. That could be it. Yours may have not been hooked up yet at the wheel, display or computer. I see the wire in your picture attached to the right fork but not hooked up correctly maybe when the front wheel was put on.

Mudflap · 07-03-2023, 06:56 AM

Quote:

Originally Posted by Mikd

Question, has anyone experienced the electronic speedo not registering speed? Seems to happen about 1/3 of the time.

Pic doesn't show up for me but make sure the tabs on the speedo sensor are in the slots in the wheel hub and that the tab on the speedo sensor housing is properly positioned so it is held from turning by the fork.

Mikd · 07-04-2023, 10:02 PM

Pic refused to load for some reason. The speedo pickup is positioned correctly on the wheeel hub. It seems to be an electronic issue, if I stop and cycle the key off and restart it works properly.

Added some led lighting to the inside the red reflector on the top case, anything to help with visibility for distracted drivers

Dblack5939 · 07-07-2023, 10:41 AM

I've gotten over 3,000 miles on mine but, this scooter is hard to work on because of how it's designed.

Dblack5939 · 07-07-2023, 01:32 PM

Quote:

Originally Posted by RobEmBlind

Hello, I am new to this forum but have been following . I have a clash 200 efi and my belt shredded into pieces and there isn't anyone that knows the correct size. I took it all apart which was easy. I didn't have to remove the peg but I did take a bolt off by the peg and it dropped it enough to remove the cover. Does anyone know what size belt it is? Thanks in advance.

Hey, I was wondering if you took a pic of how you got the belt off without removing the peg? If so could you post something?

clash 168cc · 07-07-2023, 01:49 PM

I had to wiggle while holding in the kick start shaft. The first time the kick start came apart. You may have to re-weld/move the foot peg. Someone else said remove a motor mount to drop the engine lower.

06-30-2023, 10:33 PM	#141
Mikd Join Date: May 2023 Location: NY Posts: 118	Arrived today, packaging was clean. Hopefully assemble it tomorrow. Attached Thumbnails
	1

06-30-2023, 10:38 PM	#142
Mikd Join Date: May 2023 Location: NY Posts: 118	Great looking scooter Attached Thumbnails
	0

05-27-2023, 11:08 AM	#136
Mudflap Join Date: Sep 2014 Posts: 1,870	I pulled the fuel gauge sending unit/fuel pump to see if it was hanging up or could be adjusted but no joy. The ohm reading from the potentiometer was consistent throughout it's range of movement, and it moved freely. Couldn't bend the float rod enough to make a difference because doing so would make it hit the filter or the top of the tank. Range is 8.5 ohms to 87 ohms.
	0

06-18-2023, 01:24 PM	#138
Mudflap Join Date: Sep 2014 Posts: 1,870	About 3000 miles now and then rear tire is nearly worn out. I'll be installing the Michelin next week. No complaints about the original Seyoun tires in the handling department, they are soft and grippy.
	0

06-28-2023, 02:28 PM	#139
Mikd Join Date: May 2023 Location: NY Posts: 118	Have a Clash 200 on order. Fingers crossed its a decent little runabout. Glad this place is here for info as I like to tinker.
	1

07-02-2023, 04:54 PM	#143
Mikd Join Date: May 2023 Location: NY Posts: 118	Question, has anyone experienced the electronic speedo not registering speed? Seems to happen about 1/3 of the time.
	0

07-02-2023, 04:55 PM	#144
Mikd Join Date: May 2023 Location: NY Posts: 118	Pic
	0

07-02-2023, 06:24 PM	#145
clash 168cc Join Date: Jul 2022 Posts: 94	Check your connections. must be a speed sensor on the wheel somewhere. Mine is showing over actual speed between 3 to 7 mph like most of them. There's a wire going to the right side of the front axle. That could be it. Yours may have not been hooked up yet at the wheel, display or computer. I see the wire in your picture attached to the right fork but not hooked up correctly maybe when the front wheel was put on.
	0

07-04-2023, 10:02 PM	#147
Mikd Join Date: May 2023 Location: NY Posts: 118	Pic refused to load for some reason. The speedo pickup is positioned correctly on the wheeel hub. It seems to be an electronic issue, if I stop and cycle the key off and restart it works properly. Added some led lighting to the inside the red reflector on the top case, anything to help with visibility for distracted drivers
	0

07-07-2023, 10:41 AM	#148
Dblack5939 Join Date: Nov 2022 Posts: 7	I've gotten over 3,000 miles on mine but, this scooter is hard to work on because of how it's designed.
	0

07-07-2023, 01:49 PM	#150
clash 168cc Join Date: Jul 2022 Posts: 94	I had to wiggle while holding in the kick start shaft. The first time the kick start came apart. You may have to re-weld/move the foot peg. Someone else said remove a motor mount to drop the engine lower.
	0