New Boom Vader Showing up on Wednesday - help

Seant · 06-06-2020, 10:17 PM

Ill keep it brief. Bought an automatic chuckus to get around town/to school. It was fun and did what I think most mopeds do to first time riders. Made me immediately sell it, decide riding automatic just wasn't for me, and thus, I decided to purchase this boom 125cc brand new from the factory. It is showing up 85% assembled and I can pick up the basic mechanic set up pretty quick/have watched countless youtube videos. I have two questions. First, I really liked the throttle play on the chucks. It gave me a little more than a quarter turn before full engagement. Can I adjust that on the boom? Or is that a bad habit? 2nd what are the "mods" aka the things I should do to the bike once assembled without yet putting any after market parts on it? Thanks my dudes and ladies!

Big Bird · 06-06-2020, 11:42 PM

I have one scheduled to arrive next week too. So I will tell you what I plans to do to mine once it arrives. Engine mount bolts, the stock ones break. M8 10.9 metric or 5/16 grade 8 standard. Fuel filter, the stock ones apparently leak once fuel deteriorates the glue. Carburetor, they run lean to pass epa standards. You can slot the screws to take the stock one apart to rejet. I'm upgrading the carb to a vm22 knockoff and rejetting it. Treadlock on all bolts without nylock nuts. Change oil immediately before first run.

You can adjust for a lot of throttle play but at some point it won't be opening the throttle slide all the way.

Seant · 06-07-2020, 01:04 AM

Basically what i just put in the headline

Big Bird · 06-07-2020, 02:23 AM

Quote:

Originally Posted by Seant

Basically what i just put in the headline

This is the kind I ordered since it's the same type I run on my shifter kart with good luck.

https://www.ebay.com/itm/Universal-1...1-8969ab70956b

As far as the sprocket not sure. I'm leaning towards a 16t cause I'm a heavier rider. Most people seem to run the 16 or 17.

wlfpck · 06-09-2020, 10:28 AM

You can get quarter turn throttle tubes and swap them over. A lot of people on the ZS190 groups used the motionpro ones.

Typical mods and engines swaps. Look in the link below.

http://chinariders.net/showthread.php?t=24100

Seant · 06-10-2020, 06:01 PM

It’s an M4 he says it’s “universal” which feels very “ununiversal” here’s a picture

Seant · 06-15-2020, 06:06 PM

I was able to get the sprocket on, pro taper bars, and everything ready to go accept for the freaking oil change. I cannot for the life of me get the bolt off. Its positioning next to the exhaust isn't helping either. Can't get a breaker bar or ratchet to it, any suggestions?

RedCrowRides · 06-16-2020, 12:14 AM

There is two bolts under there, one is the oil drain plug and the other is something else, iirc the drain plug is more to the center of the engine ,make sure you are taking the right one out.

Bruces · 06-16-2020, 02:04 AM

If it’s a Honda horizontal clone the other bolt is for the timing chain tensioner .

Big Bird · 06-16-2020, 03:16 AM

Quote:

Originally Posted by Seant

I was able to get the sprocket on, pro taper bars, and everything ready to go accept for the freaking oil change. I cannot for the life of me get the bolt off. Its positioning next to the exhaust isn't helping either. Can't get a breaker bar or ratchet to it, any suggestions?

Put a box end wrench on it and tap the wrench with a hammer while you apply force.

Seant · 06-18-2020, 04:40 PM

Got it off, took the wrong one off first (I think I put everything back in correctly, any harm in what I did?) - been teaching myself how to ride all day now. I have some super newb/ dumb questions. I am going to post a thread of all the questions beginners may be afraid to ask. Maybe it will get some traction.

franque · 06-18-2020, 06:05 PM

What's the I.D. of the muffler you're hoping to put on? It looks like it is waaay too big.

06-06-2020, 10:17 PM	#1
Seant Join Date: Jun 2020 Posts: 11	New Boom Vader Showing up on Wednesday - help Ill keep it brief. Bought an automatic chuckus to get around town/to school. It was fun and did what I think most mopeds do to first time riders. Made me immediately sell it, decide riding automatic just wasn't for me, and thus, I decided to purchase this boom 125cc brand new from the factory. It is showing up 85% assembled and I can pick up the basic mechanic set up pretty quick/have watched countless youtube videos. I have two questions. First, I really liked the throttle play on the chucks. It gave me a little more than a quarter turn before full engagement. Can I adjust that on the boom? Or is that a bad habit? 2nd what are the "mods" aka the things I should do to the bike once assembled without yet putting any after market parts on it? Thanks my dudes and ladies!
	0

06-07-2020, 01:04 AM	#3
Seant Join Date: Jun 2020 Posts: 11	type of fuel filter/ should I throw on the 17t sprocket right from the jump Basically what i just put in the headline
	0

06-09-2020, 10:28 AM	#5
wlfpck Join Date: Mar 2018 Posts: 249	You can get quarter turn throttle tubes and swap them over. A lot of people on the ZS190 groups used the motionpro ones. Typical mods and engines swaps. Look in the link below. http://chinariders.net/showthread.php?t=24100 __________________ 2020 Honda Grom 2017 Icebear Fuerza (Daix PMZ125-1) - Sold
	1

06-15-2020, 06:06 PM	#7
Seant Join Date: Jun 2020 Posts: 11	update I was able to get the sprocket on, pro taper bars, and everything ready to go accept for the freaking oil change. I cannot for the life of me get the bolt off. Its positioning next to the exhaust isn't helping either. Can't get a breaker bar or ratchet to it, any suggestions?
	0

06-16-2020, 12:14 AM	#8
RedCrowRides Join Date: Jun 2018 Location: Florida Posts: 759	There is two bolts under there, one is the oil drain plug and the other is something else, iirc the drain plug is more to the center of the engine ,make sure you are taking the right one out. __________________ 2001 Mustang GT 2004 Sportster 2018 VADER 2020 Orion RXB250L
	0

06-06-2020, 11:42 PM	#2
Big Bird Join Date: May 2020 Location: California Posts: 169	I have one scheduled to arrive next week too. So I will tell you what I plans to do to mine once it arrives. Engine mount bolts, the stock ones break. M8 10.9 metric or 5/16 grade 8 standard. Fuel filter, the stock ones apparently leak once fuel deteriorates the glue. Carburetor, they run lean to pass epa standards. You can slot the screws to take the stock one apart to rejet. I'm upgrading the carb to a vm22 knockoff and rejetting it. Treadlock on all bolts without nylock nuts. Change oil immediately before first run. You can adjust for a lot of throttle play but at some point it won't be opening the throttle slide all the way.
	1

06-16-2020, 02:04 AM	#9
Bruces Join Date: May 2018 Posts: 1,574	If it’s a Honda horizontal clone the other bolt is for the timing chain tensioner .
	1

06-18-2020, 04:40 PM	#11
Seant Join Date: Jun 2020 Posts: 11	got it off - took the wrong one off first Got it off, took the wrong one off first (I think I put everything back in correctly, any harm in what I did?) - been teaching myself how to ride all day now. I have some super newb/ dumb questions. I am going to post a thread of all the questions beginners may be afraid to ask. Maybe it will get some traction.
	0

06-18-2020, 06:05 PM	#12
franque Join Date: Nov 2017 Location: Marseille, France -> Conakry, Guinea Posts: 1,481	What's the I.D. of the muffler you're hoping to put on? It looks like it is waaay too big.
	0