![]() |
#46 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
After doing some research, I have discovered Lifan forks have the following designations written upon them.
Left Fork: CAQ-30-L CM-1 Right Fork: CAQ-30-R CM-1 ![]() My Zong's forks have the same travel (6.5 inches) as Lifan CM-1 forks, but are slightly different in design. My forks have the following designations written upon them. Left Fork: CAQ-30-L CM-2 Right Fork: CAQ-30-R CM-2 The inner tubes of my CM-2 forks have a longer, outer sleeve on the bottom of the fork tube than the CM-1 forks. Therefore, when my forks use up the 6.5 inches of available travel, the upper fork tube comes close to contacting the lower sleeve on the inner fork tube. ![]() Perhaps the CM-2 designation indicates my forks are a later design. :?: I previously thought the CM-1 forks might have a longer travel than my CM-2 forks, but apparently they don't. ![]() Spud ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#47 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Here are the dimensions of the CM-1 and CM-2, 37mm, USD Chinese forks.
Diameter of inner fork tube: 37mm Diameter of fork at upper triple clamp: 48mm Diameter of fork at lower triple clamp: 51mm Overall length from tops of fork caps to bottom of fork tube: 33.5 inches Axle diameter: 12mm Both pairs of forks have the same travel and dimensions. However, one would probably need to switch front wheels if he decided to switch between these two forks, since the brake caliper and speedometer tabs are different. ![]() Spud ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#48 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Several days ago I changed the fork oil in my Honda XR650L and CRF250X motorcycles, so I decided it was probably time to once again change the fork oil in my Zong.
![]() After 12,000 miles of riding my Zong, the Mobil1 Synthetic ATF appeared to be in very good condition. ![]() ![]() While changing the fork oil, I inspected the bushings, fork oil seals, and dust wipers. All of these components were in excellent condition, and I don't have any oil leaks. ![]() ![]() ![]() ![]() At the last fork oil change, I installed 200 ml of Mobil1 Synthetic ATF, with a viscosity of 36.3 cSt at 40 degress Celcius. http://www.mobil.com/USA-English/Lub...hetic_ATF.aspx ![]() This time I installed 225 ml of Valvoline MaxLife Dex/Merc ATF with a viscosity of 28.2 cSt at 40 degrees Celsius. http://www.valvoline.com/pdf/maxlife_atf.pdf ![]() I had intended to add much more fork oil, but I discovered the oil level rises greatly after the fork springs are installed. Therefore, I installed enough ATF to cover the fork springs, which left an air space of about 90mm after the springs were installed. Perhaps I might add another 25 ml the next time I change the fork oil. However, I think about 250 ml is the maximum amount of fork oil one should install in these Zongshen forks. ![]() ![]() After changing the fork oil, I went for a test ride. ![]() ![]() ![]() The lighter, Valvoline MaxLife Dex/Merc ATF does seem to have softened the damping a little, which I enjoy. ![]() ![]() Spud ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#49 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Thanks for the update, Spud. When simply changing the oil (and not the seals), do you drain and refill from the top of the fork leg? Do you have a drain point on the underside of the very bottom, or perhaps a schrader valve?
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
![]() |
#50 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
![]() ![]() As with the rest of the motorcycle, the Zongshen forks are very easy to service. ![]() I then resumed working on the outer fork tube. I removed the dust wiper, and was prepared to clean it. However, the dust wiper and the area beneath it were spotlessly clean. ![]() The inner fork tube has a beveled edge, and the guide bushing is located inside the outer fork tube. Therefore, I merely inserted the inner fork inside the outer fork to reassemble the fork. Next, I added 200ml of ATF, and worked the oil into the cartridge by extending and compressing the damper rod. Then I installed the fork spring. Next, I added enough ATF to cover the top of the damper rod and the spring. Then I installed the preload spacer bushing, and the preload spacer. Finally, I attached the fork cap to the top of the damping rod, completing the assemble. After installing the forks back in the triple tree, I reattached the wheel, brake caliper, et cetera, and the job was complete. ![]() Spud ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
![]() |
![]() |
#51 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
The Zong's forks don't have oil drain plugs. However, the forks on my Honda XR650L and CRF250X don't have drain plugs, either.
![]() ![]() My Zong's forks are far easier to service than either of the forks on my Honda bikes. The suspension feels remarkably better after you remove the Chinese oil from the Zong's forks, and install some ATF. ![]() ![]() Spud ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#52 |
Join Date: Mar 2009
Location: Southeastern Washington desert
Posts: 14,761
|
There's no other way to put it, but NO PLACE is more beautiful than Idaho.
__________________
Happy to serve. |
![]() |
![]() |
#53 |
Join Date: Mar 2008
Posts: 2,436
|
They're made by: http://www.yuanchina.com/aspx/yajz/
|
![]() |
![]() |
#54 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
![]() Are you sure Yuan manufactures the forks for my Zong? I can't find any USD (upside down) forks at the Yuan website. :? http://www.yuanchina.com/aspx/yajz/list.aspx?classid=9 Spud ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
![]() |
![]() |
#55 |
Join Date: Mar 2008
Posts: 2,436
|
The trademark matches ur picture.
http://www.yuanchina.com/aspx/yajz/s...assid=11&id=41 |
![]() |
![]() |
#56 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
![]() ![]() My Zongshen forks don't have any adjustment capabilities, and the brake caliper is placed higher on the bottom of the fork. ![]() ![]() Spud ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
![]() |
![]() |
#57 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
The forks on my Roketa are not salvageable, so I installed a pair of low-mile Gio forks that have adjustable clickers on top of the fork legs. i haven't yet figured out how to dismantle them for an oil change. The caliper bolts onto the same spot as the originals, but I had to make a spacer on the speedo side, since these forks were originally used with a non-speedo 19" rim.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
![]() |
#58 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
You drain the oil pretty much the same way with all of these forks. Unscrew the fork cap, then slowly lower the outer fork tube. Pour the oil out of the fork as you remove the fork spring. Unless you have a twin chamber fork, you drain the rest of the oil by pumping the damping rod. If you have a twin chamber fork, you need to remove the damper from the fork, and remove the cap from the damping unit before you pump the oil out of the inner chamber. If possible, measure the oil level after you remove the spring, and before you pour the old oil from the fork. Also, collect the old oil, and measure it's volume so you know how much new fork oil to install. ![]() ![]() Spud ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
![]() |
![]() |
#59 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
I presume that I must remove the clickers, and that will reveal a nut underneath that I can remove. I'll report in my Roketa thread.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
![]() |
#60 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
![]() ![]() Spud ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
![]() |
|
![]() |
![]() |
|
|