Dragon Chopper (3/4 chopper) - Page 19

jlbateman333 · 08-30-2011, 07:47 PM

So should I just go ahead and replace all the wiring on the chopper? By the way I will be asking alot of questions cause I have never had a motorcycle and this is my first experience with one due to me being only 4ft 6in and I have finally found something that actually fits. Yes you read right. lol

jlbateman333 · 08-30-2011, 08:46 PM

Here are picks of the chopper. Picked it up for 800.00

Weldangrind · 08-30-2011, 09:48 PM

Good score! Please start a new thread in the Street forum for more exposure.

jlbateman333 · 09-08-2011, 05:19 PM

Question I bought mine off a private owner. I got a bill of sale but been reading online I need an mco to get it titled. The chopper has never been titled and he did not have the mco. How hard will this be to get registred? I live in Indiana.

geekman · 10-16-2011, 12:09 AM

Can anyone tell me where I can get a Jack Shaft?

jlbateman333 · 10-18-2011, 09:02 PM

Has anyone switched out the handlebars for riser bars with handlebars? The stock ones are welded and want to be able to switch handlebars out with using risers.

Whistler · 10-19-2011, 03:47 PM

Just picked up one of these neat little bikes a week or so ago. Interesting that the first thing I noticed was some electrical tape on the wiring harness. Considering the discussion here and on investigation just re-wired the whole bike. I've built quite a few Harleys over the years, this thing is more fun than I've had on a bike since I was a kid. Cheap and a bit of a basket case but I'd intended to replace the cosmetics from the start.

A couple of questions:

I read a few mentions of jack shaft mods, anybody work up something to fix that weak point w/o fabricating a new one?

Has anyone done any frame mods? The front of the frame just looks "unfinished" and I'm thinking I'll rework that over the winter as well as touching up any spotty welds,

Some great posts here! I'll share here once I get rolling on it!

Flare · 03-15-2012, 12:33 PM

I have a scorpion chopper as well and it will not spark!

Does anyone know where I can get a wiring diagram?

jlbateman333 · 07-17-2013, 09:46 AM

Just checking in to see if anyone still has their choppers and riding. I have had to put mine on hold to work on it but gonna start getting it road ready.

Weldangrind · 07-17-2013, 10:40 AM

Thanks for checking in.

I haven't seen any choppers since you posted yours, but I'm interested to follow your progress.

jlbateman333 · 07-17-2013, 10:59 AM

Its going to be a slow work in progress but want to get this thing road ready so I can actually ride and not waste the money I spent on it.

Weldangrind · 07-17-2013, 08:50 PM

Please start a new thread for it, where it will get the attention it deserves!

zingshoen · 07-18-2013, 09:31 AM

that s a great looking chopper, even better if you can get it on the road.

Forklift352 · 08-23-2019, 05:00 AM

I'mmmmm baaaaack!
Any Dragon riders left?

Pathfinders · 08-23-2019, 05:10 PM

Don't have one but want one.

08-30-2011, 09:48 PM	#273
Weldangrind Join Date: Mar 2009 Location: Sardis, BC, Canada Posts: 25,977	Good score! Please start a new thread in the Street forum for more exposure. __________________ Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer
	1

03-15-2012, 12:33 PM	#278
Flare Join Date: Mar 2012 Posts: 1	Scorpion Chopper I have a scorpion chopper as well and it will not spark! Does anyone know where I can get a wiring diagram?
	0

07-17-2013, 10:40 AM	#280
Weldangrind Join Date: Mar 2009 Location: Sardis, BC, Canada Posts: 25,977	Thanks for checking in. I haven't seen any choppers since you posted yours, but I'm interested to follow your progress. __________________ Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer
	0

07-17-2013, 08:50 PM	#282
Weldangrind Join Date: Mar 2009 Location: Sardis, BC, Canada Posts: 25,977	Please start a new thread for it, where it will get the attention it deserves! __________________ Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer
	0

07-18-2013, 09:31 AM	#283
zingshoen Join Date: Jun 2009 Location: Brisbane, Queensland, Australia Posts: 648	that s a great looking chopper, even better if you can get it on the road. __________________ 1971 Garelli Gulp 50cc with open ports and 16 mm Bing Carbie + 1980 Honda XL 223 ZS + 2007 Zongshen LZX200G + DR400SM
	0

08-30-2011, 07:47 PM	#271
jlbateman333 Join Date: Aug 2011 Posts: 26	So should I just go ahead and replace all the wiring on the chopper? By the way I will be asking alot of questions cause I have never had a motorcycle and this is my first experience with one due to me being only 4ft 6in and I have finally found something that actually fits. Yes you read right. lol
	0

08-30-2011, 08:46 PM	#272
jlbateman333 Join Date: Aug 2011 Posts: 26	Here are picks of the chopper. Picked it up for 800.00
	1

09-08-2011, 05:19 PM	#274
jlbateman333 Join Date: Aug 2011 Posts: 26	Question I bought mine off a private owner. I got a bill of sale but been reading online I need an mco to get it titled. The chopper has never been titled and he did not have the mco. How hard will this be to get registred? I live in Indiana.
	0

10-16-2011, 12:09 AM	#275
geekman Join Date: Oct 2011 Posts: 2	Can anyone tell me where I can get a Jack Shaft?
	0

10-18-2011, 09:02 PM	#276
jlbateman333 Join Date: Aug 2011 Posts: 26	Has anyone switched out the handlebars for riser bars with handlebars? The stock ones are welded and want to be able to switch handlebars out with using risers.
	0

10-19-2011, 03:47 PM	#277
Whistler Join Date: Oct 2011 Posts: 3	Just picked up one of these neat little bikes a week or so ago. Interesting that the first thing I noticed was some electrical tape on the wiring harness. Considering the discussion here and on investigation just re-wired the whole bike. I've built quite a few Harleys over the years, this thing is more fun than I've had on a bike since I was a kid. Cheap and a bit of a basket case but I'd intended to replace the cosmetics from the start. A couple of questions: I read a few mentions of jack shaft mods, anybody work up something to fix that weak point w/o fabricating a new one? Has anyone done any frame mods? The front of the frame just looks "unfinished" and I'm thinking I'll rework that over the winter as well as touching up any spotty welds, Some great posts here! I'll share here once I get rolling on it!
	0

07-17-2013, 09:46 AM	#279
jlbateman333 Join Date: Aug 2011 Posts: 26	Just checking in to see if anyone still has their choppers and riding. I have had to put mine on hold to work on it but gonna start getting it road ready.
	0

07-17-2013, 10:59 AM	#281
jlbateman333 Join Date: Aug 2011 Posts: 26	Its going to be a slow work in progress but want to get this thing road ready so I can actually ride and not waste the money I spent on it.
	0

08-23-2019, 05:00 AM	#284
Forklift352 Join Date: Sep 2008 Location: Salem ,Oregon Posts: 121	I'mmmmm baaaaack! Any Dragon riders left? __________________ <div><em>Black Dragon</em></div><br />
	1

08-23-2019, 05:10 PM	#285
Pathfinders Join Date: Nov 2017 Location: Upstate SC Posts: 129	Don't have one but want one.
	1