![]() |
#1 |
Join Date: Oct 2017
Location: shelton, Washington
Posts: 167
|
Progress! Finally! Rocketa rehab
So i got my 27.5 pilot for my vm26 on my 200cc ohc.
Im at sea level, i have the needle at at the 4th notch. 110 main. Mix is somewhere around 2 turns out. It now idles steady without choke, im guessing 900rpm. I don’t have a tach rode it through the gears , the clutch is slipping abit, but hey! Huge step getting it to run right Ive tried to post a vid before, but it wont err...take? Idk. It started first kick after i talked to the neighbors for five minutes. Thanks for all the help given here. On to the next step. New clutch. Its a 163 ohc. Anyone have a direct link?
__________________
2006 roketa 200cc 1971 Yamaha xs650 2x 1980 xs650, 1 is a café, other is a chopper/brat 1972 Honda xl250 2x early 90's Honda rf600 parts bikes more mc junk laying around. ![]() |
![]() |
![]() |
#2 | |
Join Date: Mar 2008
Posts: 2,436
|
Quote:
![]() Most of time change fraction (wear limit: 2.6mm) ONLY will get the job done http://www.mychinamoto.com/forums/showthread.php?6812
__________________
Last edited by humanbeing; 03-07-2018 at 07:22 AM. |
|
![]() |
![]() |
#3 |
Join Date: Oct 2017
Location: shelton, Washington
Posts: 167
|
Pics for your pleasures
__________________
2006 roketa 200cc 1971 Yamaha xs650 2x 1980 xs650, 1 is a café, other is a chopper/brat 1972 Honda xl250 2x early 90's Honda rf600 parts bikes more mc junk laying around. ![]() |
![]() |
![]() |
#4 |
Moderator
Join Date: Oct 2016
Location: Houma, La.
Posts: 11,585
|
Glad to see you got it running.
![]()
__________________
2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel |
![]() |
![]() |
#5 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Have you changed the oil? If the PO used oil that isn't compatible with wet clutches, you might get lucky with 15W40.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
![]() |
#6 |
Join Date: Oct 2017
Location: shelton, Washington
Posts: 167
|
Thanks. I have 15-30 deisel oil in it. It has no friction modifiers
__________________
2006 roketa 200cc 1971 Yamaha xs650 2x 1980 xs650, 1 is a café, other is a chopper/brat 1972 Honda xl250 2x early 90's Honda rf600 parts bikes more mc junk laying around. ![]() |
![]() |
![]() |
#7 |
Join Date: Oct 2017
Location: shelton, Washington
Posts: 167
|
Woot! It started third kick cold full choke. After warm up on half choke. It settled into a smooth low idle, no choke . Romped around the area for a bit, idle was a bit low after, so I upped it a smidge. Even with a slipping clutch I could feel the front get light. I'm not after wheelies or stunts, but if it can, yeah!
__________________
2006 roketa 200cc 1971 Yamaha xs650 2x 1980 xs650, 1 is a café, other is a chopper/brat 1972 Honda xl250 2x early 90's Honda rf600 parts bikes more mc junk laying around. ![]() |
![]() |
![]() |
#8 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Angus, it's time that you showed us the other bikes in your stable. Please consider starting a thread on that.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
|
![]() |
![]() |
|
|