Vitacci Raven 250BSR exhaust mod

Topbench · 05-07-2021, 02:26 PM

Hi All, does anyone know if the new Ravens will take the same exhaust mods as the Hawks? Thanks

**JerryHawk250** · 05-07-2021, 03:38 PM

Yes it will.

Topbench · 05-07-2021, 09:16 PM

Thanks For all the support JerryHawk.

Topbench · 05-17-2021, 09:38 PM

I installed the new exhaust tonight. This was the link skyd and MegaDan have mentioned. Bolted right up front and back. The back lined up with the frame bolt. The middle mount was offset and also needed a 1/4 rubber spacer and tapped hole.

stewbrash · 05-18-2021, 04:02 PM

We want to see pictures, or it never happened! I just received a blue BSR 250; (Vitacci is no-where on the MCO...it says CHONGKING ASTRONAUTICAL BASHAN as the manufacturer, the make is a BASHAN, and the model is a BSR 250!) Jeez...I just don't get it with all the BS, scheming and misrepresentation! Will document my experience shortly...I want to receive the paperwork from the vender first. There was ZERO damage and no birth-marks!

Topbench · 05-18-2021, 11:06 PM

I will post photos when I can open the forum on my laptop and figure out how to post. I need arm extensions to work off this phone. I do know that I could use suggestions on a carb recipe. Had it tuned pretty good before the exhaust change. Seemed lean in the pilot at 27.5, I tried a 32, way too rich, moved back to 30 and still too rich. I will check the valves again and move back down again. Any suggestions would be welcome. Thanks.

Topbench · 05-25-2021, 09:18 PM

I will give the photo attachment a try. It took me awhile to get the carb recipe dialed in but I am loving it now. The pipe routing was far enough away that it hasn't bothered the air box. I have ordered some reflective tape just in case but it hasn't showed up yet but it doesn't seem like it will be needed. The muffler mount landed perfectly on the frame mount hole. The mid mount support lined up pretty good with a 1/4" gap, perfect for a rubber spacer. Well worth the few extra Benjis.

Topbench · 05-25-2021, 09:21 PM

stewbrash · 05-25-2021, 10:14 PM

The green looks awesome! The websites that sell these really need to post better photos!

05-07-2021, 02:26 PM	#1
Topbench Join Date: Apr 2021 Posts: 23	Vitacci Raven 250BSR exhaust mod Hi All, does anyone know if the new Ravens will take the same exhaust mods as the Hawks? Thanks
	0

05-07-2021, 03:38 PM	#2
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,850	Yes it will. __________________ 2025 Lifan KPT 400 2024 Linhai 300 ATV 4x4 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 (Sold) 2016 Black Hawk 250 (sold) 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	0

05-07-2021, 09:16 PM	#3
Topbench Join Date: Apr 2021 Posts: 23	Thanks For all the support JerryHawk.
	0

05-17-2021, 09:38 PM	#4
Topbench Join Date: Apr 2021 Posts: 23	I installed the new exhaust tonight. This was the link skyd and MegaDan have mentioned. Bolted right up front and back. The back lined up with the frame bolt. The middle mount was offset and also needed a 1/4 rubber spacer and tapped hole.
	3

05-18-2021, 11:06 PM	#6
Topbench Join Date: Apr 2021 Posts: 23	I will post photos when I can open the forum on my laptop and figure out how to post. I need arm extensions to work off this phone. I do know that I could use suggestions on a carb recipe. Had it tuned pretty good before the exhaust change. Seemed lean in the pilot at 27.5, I tried a 32, way too rich, moved back to 30 and still too rich. I will check the valves again and move back down again. Any suggestions would be welcome. Thanks.
	0

05-25-2021, 09:18 PM	#7
Topbench Join Date: Apr 2021 Posts: 23	I will give the photo attachment a try. It took me awhile to get the carb recipe dialed in but I am loving it now. The pipe routing was far enough away that it hasn't bothered the air box. I have ordered some reflective tape just in case but it hasn't showed up yet but it doesn't seem like it will be needed. The muffler mount landed perfectly on the frame mount hole. The mid mount support lined up pretty good with a 1/4" gap, perfect for a rubber spacer. Well worth the few extra Benjis.
	0

05-25-2021, 09:21 PM	#8
Topbench Join Date: Apr 2021 Posts: 23
	1

05-25-2021, 10:14 PM	#9
stewbrash Join Date: Oct 2016 Posts: 405	The green looks awesome! The websites that sell these really need to post better photos!
	1